LSR8233EQ0 Whirlpool Washer - Instructions

After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!

Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.

Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syphon to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.

i knew the lid sw. must be bad and had a new one in hand, but when i remove the sw. ( near the lid ) i found the wires going back to where i could not reach. was not sure how to get at them so i repaired the sw. with tape untill i could find how to get at the wire end. after reading more in this repair area i know that i need to remove the control panel which is easy to do. next time i will read all i can on repairs in this section!!

First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

first I removed the fabric softner and water seal from center of agitator, then I removed the bolt holding it on. All I had to do then is install new agitator with old bolt place water seal and fabric softner container back on and start washing clothes again. Very simple.

First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!

I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.

The repair was very easy. The only hard part was due to the age of the machine the cap covering the agitator assembly was stuck on the top.I had to use a very large pipe wrench to loosen it. Other than that the whole repair went very smooth. You will need an extension with the socket wrench in order to reach the screw holding down the agitator.I was very impressed with the service from Parts Select. I received my part very fast and it included everything I needed to complete the job.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First I removed the two screws on the back side of the switch panel and tilted it back to expose the controls. I then pryed up the top of the washer to expose the lid switch. This was a mistake because I damaged the clips and bent the metal frame. Anyway after that I unlatched the lid switch on the top side, pulled it through the bottom, removed two screws holding the lid switch in place and replaced the switch and lid switch strike. Because I wrecked the machine top I had no alternative but to drill two holes from the top and put two screws in to hold the top down. It's ugly but it works.
The best part of all this is I received the part so fast that I was able to keep up the pace of doing laundry with no interruption. Thanks for being so reliable and quick to deliver. I already told many people about your service!

I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.

we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out.
I respect that electrical parts are non-returnable as I am in the auto parts business.