LSG2704W Jenn-Air Washer Dryer Combo - Instructions

I opened the front of the washer by removing the 2 screws on the bottom front of the washer, then swinging the front upward until it was clear of the hangers at the top. The hose sits right in front. It was cracked where it attaches to the tub. I loosened the hose clamps at the tub & the pump with a nutwrench & removed the old hose. I slid the clamps onto the new hose & put the hose on to the tub & pump. I tightened the clamps, reinstalled the front & was finished.

Took off face of dryer (two lower screws below door in front) and then removed the drum which gave me access to the idler arm and idler pully. Vaccumed the interior to remove dust and lint. Replaced idler arm and idler pulley assembly. Replace old belt as drum was reinstalled. Opened rear access panel to complete final routing of the new belt over idler pulley and drive motor. Turned the machine on to check repairs and function. Closed rear access door. Pushed dryer back into place and re-leveled machine.

The task to replace the tub seal would have been relatively easy had it not been for the need of a special spanner wrench to remove the nut securing the seal. Instead of purchasing the one time use spanner wrench which was only available on line and would have delayed my repair I elected to cut the putty metal nut off with a cutting dremel tool. This was a delecate process to ensure one did not damage anything else in the process of cutting the nut. Once complete a set screw, pipe wrench and common screwdriver, hammer and tap punch was all that was used. Easy process from removal to installation and the leak was fixed saving significant $$$ over having a "maytag repairman" perform the fix...parts select video helped describe everything and cost while not cheap was significantly less for an adept DIY customer.

Sans manual, I turned to the web to find out how to open up the dryer. Maytag uses two Phillips screws on the bottom front panel. Once removed, the front pulls out at the bottom and slides free from the top. Caution, wires on the left side of the front panel prevent total detachment from the dryer. A 1/4 hex screwdriver was used to remove the cover to the blower housing. Once the cover is unbolted attached wires prevent its complete removal and can be set clear of the blower housing. Pliers were used to remove a pinch clamp from the squirrel cage fan (blower assembly) and snap ring pliers were needed to remove the retaining snap ring. The fan was easily removed from the motor's rotor. The loose fan caused damage to the blower housing which I believe was the source of the original rattle. Once the fan had been removed, the housing was removed by using a 5/16 socket on the end of an extension. The replace parts were installed in reverse order and fit perfectly. Other work included the replacement of the drive belt for the drum. PartSelect was chosen because it had the parts in stock and could be shipped overnight.

Removed washing machine front cover (2 phillips screws on bottom half of panel). Then removed two bolts that hold the top in place. Lifted hinged top, removed tub cover which is held in place with plastic mounting tabs. That was it. Put everthing back together approx. 15 Minutes.

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

For the most part, I followed the excellent repair advice already available on this site for installing these parts. Especially useful was the caution that the threaded pieces had "left hand" threads and to loosen them they had to be turned in a "CLOCK WISE" direction. My washer is 9 years old and due to calcium deposits on the threads, I did have some trouble with loosening the large retaining nut. I first soaked the nut for a few hours with a rag soaked with white vinegar. This removed some of the calcium but I still was unable to undo the nut. Finally, I soaked the nut overnight with penetrating oil and WD-40. The next morning I was able to loosen it using a drift punch and medium sized ball peen hammer. I only had one difficulty. Maybe it wasn't necessary to do so, but I wanted the rubber boot seal to be seated pretty close to the surface of the inner basket. This turned out to require more downward force than I would have expected even though I installed it dry, without use of any type of lubricant or soapy solution. Now, two weeks worth of washing and not a drop of water seen underneath the washer.

It was very easy to access the parts that needed to be replaced (blower wheel, belt, and glides).
1. Unplug the dryer power cord.
2. Removed the two screws at the bottom of the front dryer panel. Pull the bottom of the panel forward, which frees the retaining clips at the top of the panel.
3. Disconnect the two wires from the back of the panel, and remove the panel. The drum will be resting on the motor/blower hosuing.
4. Slide the belt off of the back of the tumbler, and remove the tumbler (have to angle it a bit, to clear the frame) and the belt.
5. Remove the thermostat cover (piece of angled sheet metal, in front of the blower unit).
6. Remove the screws from the blower housing, and lay it forward, to expose the blower wheel.
7. Remove the snap ring, and then the retaining ring from the blower wheel. Remove the old wheel.
8. Install the new wheel, then the retaining ring, and then the snap ring. Reattach the cover to the blower assembly.
9. Reattach the thermostat cover.
10. On the tumbler, drill out the rivets for each of the glides, and remove all glide parts. Install new glides.

This is a good time to complete any general cleaning inside the dryer cabinet, especially in the area of the motor. Since there is limited access to the motor itself, might help to use the blower function of a shopvac to blow out that dust.
Vacuum out all lint from around the felt drum seals.

11. Loop the new belt over the tumbler, and install the tumbler (the glides go towards the front of the dryer). Note: to keep the belt from falling off, I taped it to the drum with two pieces of painters tape..the blue tape that comes back off easily.
12. On the back of the dryer, remove the access panel, and complete installation of the belt to the idler pulley.
13. If you taped the belt to the drum....don't forget to remove the tape now. Reinstall front panel to dryer.

This was my first experience working with snap ring retaining rings. Even with snap ring pliers, they are difficult to remove without stretching them out. Be sure to order a new one with your blower wheel.

Also my first experience using a pop rivet gun ( to install the new glides). Found a rivet gun at Lowes for $9.99. Worked okay, and all rivets set properly. Good thing, because you don't get any extras with the glide kits.

After replacing the parts, and starting up the dryer, all of the clunking/squelling/rumbling noises were gone. There was a noticable smell while the new glides got broken in...smelled a bit like melting rubber. However, after a couple of drying cyles, the odor was gone.

Switch can be removed from outside of dryer and your video described the repair as having to work from inside dryer. But since wires were still attached to old switch, it could be popped out and wires switched. Since there were three wires on new switch to allow it to turn on and off a circuit, it was useful to check the resistance of the switch compressed or released to be certain I was attaching the two wires to the right two poles of the new switch. But that all required only a couple of minutes. Thank you.

I used a 1/4 inch socket to remove the agitator.Used a small screw driver to remove clip. Then I lifted the washer off the shaft with a magnet. Pried out the old seal with a screwdriver. This exposes the top of the tub bearing. I applied some 80-90 differential grease to the top of the bearing, pressed in new seal, installed other parts and noise gone. It sounds like a new washer. I'm glad I found you guys.

first i removed front panel by pulling it from the bottom and then removing the top. then i removed the agitator with a 1/4 nut driver. then i had to open top lid which is hinged and held together by two 1/2 inch bolts. after i opened up the top of the washer i had to remove the white plastic top of the inner tub. in order to remove the inner tub there is a large nut that i had to use a punch and a hammer to break it loose. don't forget this nut is counterclockwise to loosen.hint use a little wd40 due to calcium build up around nut. once the inner tub is removed you should see the rubber bushing. be sure to remove all rust and water calcium build up before installing new bushing. i used a wool pad. put everything back together the way you took it apart and it should fix your leak.

Turned off water supply and disconnected hoses. Removed rear cover where water valve was located. Marked and unplugged wires to valve along with interior hose connected to valve. Unscrewed two screws holding valve to rear cover. Installed new valve with all the above procedures in reverse. Very easy repair that saved us slot of money in service call fees!

There is one good description already posted. I would add:1)If the the nut holding the inner tub doesn't loosen easily just split it with a chisel and don't waste time. 2)Don't order extra washers to remount the outer tub, they come with the bearing! 3)While disassembled I ran the spindle on spin to make sure the brake assemlby wasn't the problem. It ran quietly and smoothly. 4)The inner bearing sleeve was stuck on the spindle and didn't want to free up. I used a rotary tool to cut a groove in the old bearing sleeve then chiseled on the groove edge and it split nicely. It was very brittle. The washer seems to work well now. Next time I see a leak I am going to repair it right away!

Before anything, I unplugged the dryer and tipped it over on its front. Then I removed the lower access panel and saw that the belt was broken. I removed the belt. I replaced the panel and put the dryer upright. When I ordered the belt off this site, I used one of the repair stories. With a phillips-head screwdriver, I removed the two screws below the door on the front panel. The panel is held in place by two clips at the top. Gently pull the cover off, since there are also two door-open sensor wires connected to the front panel. I removed the hex nuts holding the tumbler in place. When I started to put the belt on, and was having a bit of trouble, my neice pointed out the diagram on the bag the belt was in. From then on it was a piece of cake. I got the belt in place, replaced the tumbler and front panel, and plugged it in. Good as new!

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.