LSG2704W Jenn-Air Washer Dryer Combo - Instructions

My washer filled up and wouldn't drain at all.

I tried checking the fuses, then read that the belt could be broken or worn. I checked under the hood and the belt was broken right in two. I drained the washer manually then ordered the new belt.

I was able to replace the belt in no time with no effort at all.

I followed the supplied directions to remove covers, unbolt tub springs, and expose the area needed to replace the damper pads. I cleaned the area with acetone and applied a rubber adhesive (not supplied). I used tire patch compound because that is what I had on-hand. I positioned the pads and after they had dried 1/2 hour, lubricated them with the supplied grease. I reassembled the washer and it is now smooth and well behaved.

First I unplugged the machine. I removed the two screws in the front panel and tilted the bottom of the panel out unclipping it at the top. I removed the lint duct whichis held in place with several 1/4" hex head screws. Then I removed the blower cover, also held on wth 1/4" hex head screws, exposing the blower wheel. Using snap ring pliers I removed the snap ring at the end of the motor shaft. Using needle nose liers I removed the spring clamp around the center hub of the old blower wheel and pull the blower wheel off the motor shaft. After cleaning as much lint out as I could I put the new blower wheel on the motor, secured with spring clamp and snap ring. Then I put the blower cover and lint duct back on and put front panel back on.

My 20 year old reliable Maytag 512 lgp dryer was not heating anymore. At first the heating element would glow red but not hot enough to ignite the gas. I replaced the element and it worked for a few loads but then stopped reigniting after the first cycle.

After some research and diagnosis (checking connections, amperage flow on each electriical part, etc.) I determined that the two coils were faulty. I ordered parts and replaced them (easy to do) and it worked again, for another few loads. Then nothing worked. The coil did not get hot and I did not hear the clicking sound that initiates current flow to the ignitor through the coils.

I checked the coils and ignitor again, they were fine. Frustrated, I called in a repairman to diagnose the problem. $55 and 15 min later he narrowed it down to the High Limit Thermostat. To demonstrate he bypassed the thermostat by directly connecting the two leads together and the ignitor fired right up.

His price to replace the thermostat? $45 part plus $130 labor. I bought the thermostat online for less than half his parts cost and the labor took me 5 minutes. Simply unscrew the small screws with a small socket set or nutdriver and replace the thermostat. Just two connectors, real simple.

All in all it was very easy to replace the parts, just tricky to diagnose unless you are good with electrical work.

Followed the instructions on the video, and saved 500 hundred dollars. I was already shopping for a new dryer. Thanks so much!

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

Tilted the machine back on a 45 degree angle while a friend held it tilted I grabbed the pump belt and removed it and then removed the main drive belt by turning it and derailing it off track . but the new belts on using a reverse technique by rerailing the new belts on to the pulleys. pushing the main motor away from the spring tension made it easier . very simple staight forward job. similiar to putting a chain on a bicycle!

Replacing the blower fan took way too long, like 4 hrs, because I didn't know how to disassemble the dryer and get to the problem. Replacing the idler bracket and assorted retaining rings and washers was fast, something like 1 hour. Disconnect the power cord, exhaust hose, and gas line. Remove two screws at the bottom of the face of the machine, unplug the electrical harness to the door light, switch and ground and remove the front of the machine. Remove the access panel at the back of the machine and remove the belt from the idler pulley. Remove the four screws holding the front drum support assembly and remove the drum. Replace some old retaining rings and the spring washers on the drum support rollers. Around back assemble the idler pulley assembly with some new washers and the old roller which seemed in good condition. Put it all back together. About one hour.

Tilted the washing machine back at 45 degree angle. Removed three screws from the underside of machine. Slipped belt off pump. Lessened two hose clamps and removed hoses.
Lifted old pump out. Dropped new pump in place.
Screwed in the 3 screws. Slipped on the belt.
Attached two hoses. Tightened hose clamps.
Set washing machine upright.

No more leak.
My problem was I could not prove the pump was the source, but after switching it out I have had no problems (good enough).

remove front, 2 screws hold top down, 1 screw holds adgitator on, hammer and punch to remove stem nut (clockwise) used wd40, lift tub out, hammer and punch to remove stem (clockwise), pull seal off, put liquid soap on seal and reverse process, no more leaks!!

By doing the work yourself, not only gives you the good feeling you did it yourself and works just like it was when it was new and to know there's part's you can still get from part places like these! Like I say to my wife ( if they meaning a repair shop can do so can't I ). Course changing a motor in a car that's a different story, I'll let someone else to do that. To do the repair I took off the front cover of the washer exposing the tub, motor and other things. But the very first thing I did is unplug the power ( I hate the bad storys that if I only turned off the power ? ) then I took off the cover over the motor and changed the switch. And all in reverse. And plug power back in. Started up just fine.

Unplugged the dryer!!!! Removed two screws from lower front panel. Pulled bottom of front panel forward which allowed clips holding top of panel to release. Unlcipped wires attached to door switch on front panel. Set aside front panel. Removed 4 screws(2 on left & 2 on right) from the drum retainer ring. Set aside retainer ring. Removed thin metal cover protecting blower wires. Removed several screws holding blower cover. Note blower is located on lower left below the lint screen. Used snap ring pliers to remove snap ring securing old blower wheel(an external snap ring). Removed old blower wheel from motor shaft. Inserted new blower wheel on motor shaft. Replaced snap ring. Replaced blower cover. Replaced thin metal wiring cover. Replaced drum retainer ring. Reconnected door switch wiring. Replaced front panel. Done. A hint on the maytag dryer. If your drum wiggles out too far the belt on the drum might not stay aligned. There is a groove on the drum...the belt should NOT sit in this groove...it should ride on the drum about an inch in front of the groove!!!

Using the instructions accompanying the belt I bought from you,I removed the casing an front support for the drum. I then tried to follow the instructions to install the new belt from the front and found it to be absolutely impossible.I saw that there is a removeable plate on the lower right corner of the back that,if removed, would expose the motor and idler pulleys that are the object of the installation so I removed it and,without much difficulty, installed the belt. One problem in doing so involved the belt's tendency to slide into the groove in the drum when manipulating it onto the pulley set so I enlisted the aid of my wife to hold it in place from the front while I successfully and rather easily did so.

That would take forever to write in everything you have to do, but I did go to a website that had the steps you must do to complete the repair. You can google tub seal kit and mounting stem and the brand of your appliance and i'm sure you will come across the steps to complete the repair. I would advise you to first order a spanner wrench it makes the job much easier and you really can't complete the job without it. So do that first and then take the machine apart if you suspect it's a tub seal leak and then order your parts. if i had a spanner wrench available to me from the beginning it would have gone much smoother from the start.

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.