Models > LMXS27676D > Instructions

LMXS27676D LG Refrigerator - Instructions

All Instructions for the LMXS27676D
16 - 30 of 46
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Mullion Strip Spring Broke
Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.
Parts Used:
Refrigerator Spring
  • William from VICKSBURG, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The ice tray was cracked and leaking water
1. Remove 3 screws (2- bottom 1-middle)
2. Loosen 1 screw (top middle left)
3. Remove the whole assembly by pulling down carefully
4. Disconnect the multi-wire plug from the back of the door. It has a locking tab on top that you may have to use a flathead screwdriver to unlock, being careful
not to touch the wiring.
5. Reverse this procedure to install the new icemaker assembly.
Parts Used:
Ice Maker and Auger Motor Assembly
  • Luis from San Antonio, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
This is the second time they have mailed me the wrong spring. I talked to someone the last time and explained everything About my refrigerator. I had a Repair man come and try to put this part on my refrigerator this time and he told me that this spring is not for this side of my door. The first tim
Expensive to have repair man come out and find out that I’ve been mailed wrong spring again. My icemaker is on the left hand side this is the side of refrigerator- I need the spring for left side with the ice maker. Twice they have mailed me the Wrong spring that goes on the right hand side I have tried to explain this to the person that waits on me. Do I have to pay for another spring and mail this one back ?i have mailed one back and postage is getting expensive.
Parts Used:
Refrigerator Spring
  • Delores from WINNIE, TX
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The refrigerator ice maker needed replacing
The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.
Parts Used:
Refrigerator Ice Maker Kit Assembly
  • Larry from GODDARD, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking
Swapped old one with new one. New one had extra plug not needed.
Parts Used:
Water Inlet Valve Assembly
  • Johnny from MOUNT OLIVE, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
tray was a tight fit but we got it in
work with the tray gently. To ensure this did not break.
Water filter installed was installed exactly the way the instructions stated to be
Parts Used:
TRAY ASSEMBLY, FRESH R Refrigerator Water Filter LT700P
  • Katharine from FAIRFIELD, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My ice maker wouldn't release the ice, nothing was frozen and the motor would just bind
I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!
Parts Used:
Refrigerator Ice Maker Kit Assembly
  • Jodi from WINTER GARDEN, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker and Water dispenser stopped working
Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/
Parts Used:
Water Inlet Valve Assembly
  • Donald from BETHPAGE, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice tray was not rotating any longer
Took the old one out and put the new one in.
Parts Used:
Refrigerator Ice Maker Kit Assembly
  • Angela from SAINT JOSEPH, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Slow water for drinking
Just like on YouTube very easy to do
Parts Used:
Water Inlet Valve Assembly
  • Steven from SEBASTIAN, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker not working
Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice
Parts Used:
Ice Maker and Auger Motor Assembly
  • Franck from ST PETE BEACH, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring broken on front plate
Unscrew two Phillip screws on center hing , push frt plate down and replace.
Parts Used:
FRONT PLATE ASSEMBLY
  • RODNEY from GERMANTOWN, TN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken sliding rails for vegetable and deli tray. Glass replacement for vegetable trays
Removed trays and replaced broken sliding parts and replaced glass
Parts Used:
Glass Shelf Guide Assembly,TV GUIDE ASSEMBLY,RAIL
  • Nancy from COUNCIL BLFS, IA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Previous glass shelf shattered into a million pieces while cleaning.
Just laid the shelf down. Fit like a glove!
Parts Used:
Glass Shelf
  • Susan from SAFETY HARBOR, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The glass shattered & needed to be replaced
Just popped it in, just as easy as that!
Parts Used:
Glass Shelf
  • David from HAMPTON, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the LMXS27676D
16 - 30 of 46