LMHM2017ST (00) LG Microwave - Instructions

the repair kit was useless the toggles were to big to go through the top the threads on the bolts interrupted the toggle i had to drill the holes thole to except the toggles I got bolts at the hardware store what a mess
Bob

Just replaced the inner turn table glass tray

I opened the door and slid the tray into place.

Simple remove one screw, remove the little broken plastic and then replace the entire filter cover with the new one and tighten the one screw on the top.

i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell

Inserted plastic lugs in place, slid to right and it fit perfectly!!!

Simply set new tray on microwave rollers and insured glass groves fit on roller .

I want to preface this review by stating that I do some DIY from YouTube, but have no experience in electronic repair. The microwave is over the stove with the extendavent. First I unplugged the microwave, removed the vent and started to unscrew the microwave from the mount. I used a power drill to speed things up. I was able to remove the microwave on my own. I unscrewed the lid on the microwave and took the lid off and there is the magnetron. I opened up needle nose pliers to have each end touch the terminals of the capacitor (holds the power, Dangerous). I made sure to keep my hands on the rubber handles and avoid touching the metal part of the pliers. I used the pliers to remove the plug of the capacitor to the magnetron as well. The magnetron has 4 screws (2 top, 2 bottom). There is a magnet that can hold the screws to keep from falling but I’d still recommend a screwdriver with a magnet on the end. The magnetron has another set of wires connected by a metal bracket like a holder, not really connecting any wiring to the magnetron itself. I had to unscrew 1 screw to removed that. Adding everything back on was easy, same steps back. I plugged in the microwave and tested a cup of water before I mounted it back above the stove. Voila! I did need my wife’s help to hold the microwave on the hinge while screwing into the mount. It doesn’t take a lot of muscle for the help. $85 for the part and ~40 mins to fix a $400 microwave!

Removed the phillips screws from the base.

Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)

Replace the spacer, which is a separate part from the motor.

Reinstall the spacer and motor.

Reinstall the bottom panel.

Enjoy!

Wanted to see the instructions before I install it.

Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.

Easy, and the microwave still doesn't work.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

We had made this determination with the help of a repairman on the phone. I ordered the part and waited for it. It was stuck in West Virginia. After several days after it was expected a repairman fixed my range to the tune of $168. It should have cost $30 (the cost of the part and shipping).
Unfortunately I probably won't order from PartSelect again.

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.