LFX25960SW LG Refrigerator - Instructions

snap it on!

easy and quickly Thank you for your prompt delivery and excellant service

Removal was pretty easy-- replacing crisper drawer took a little care so as not the snap off the hinge- thank you for the speed in which I got my part, no sooner did I order my part- it showed up at my door. your service was outstanding, put you in my favorites just incase I need to order again.

Replacing the broken part with the new part was really quite simple. The part just snapped in. The part was identical to the original. I must add that the web site was very easy to navigate, find the part, and order it. The part arrived very quickly. Guy

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.

Be sure to order two if both are broken. The picture shows two but only comes as a single item. Super easy to replace.

Removed white plastic trim and installed new latch / cam shaft

slightly depressed tabs, lined up to mounting holes, released tabs.

Replacement part from PartSelect was OEM, identical to original part. Installation was very quick. Inserted hinge on left side and then depressed the right side to slip it into place. Presto, it was done. Most impressed with PartSelect on the OEM replacement part and very prompt delivery.

I removed the old lamp cover and case. Discovered that the last repair person had not re installed it correctly so the case had melted from the bulbs. I Removed the screws that was supposed to hold it up, assembled the case and cover, inserted the screws and anchored them in where they belong. Problem solved!

I got my brother to do the repair....lucky me.

My husband took out the ice maker. We ordered the part. He looked on YouTube for instructions. Including looking up instructions, I think it took him way less than an hour.

I first took off a plastic trip strip which just popped off with a little pull. Then I pulled the gasket off slowly all around the perimeter of the door and snapped off the guide strip with the help of a screwdriver. I installed the gasket next first the guide strip then followed up with the pushing the gasket into the groove all around the door. Did the same procedure on the other door. The gaskets came very well packed and undamaged. It took approximately 2 weeks because one gasket was on back order. Thank you for your help with these parts. It would have cost me 3 times as much if the repairman performed this repair.

The vegetable bins at the bottom of the refigerator weren't sliding smoothly, as the two outlying rollers had snapped off the large plastic frame that houses said bins. Unclipped/unsnapped all the covers and glass shelving and remaining rollers attached to the frame and reinstalled them on the new frame. The only tough part was removing/installing a couple of large transpaent pieces of plastic that sit directly under the glass shelf. I'm not sure what their function is, except perhaps to look nice. But I had to pull the frame out with surprising force to snap the pieces in and out. Had to use a screwdriver for leverage and was afraid I was going to crack the frame. There must be a trick to it, because I'm a strong guy and it was still hard for me to do; there must be an easier way. Nevertheless I got them in ok, and bins pull out easily again. I was impressed when comparing the old frame to the new one, btw, as the new one's roller-attachment point is far sturdier than the old one. Obviously this was a weak point that has been well-addressed.

No installation instructions. I just took everything out of the shelf holding the drawers and figured it out myself. Unfortunately today's products are made with cheap brittle plastic. This is the second time I have ordered parts for this refrigerator from you and I am glad you are so efficient and shipped orders quickly.