LFUH21F7LM2 Frigidaire Freezer - Instructions

I order another one thanks

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Per YouTube, used stiff putty knife to push down & pry out from top. Housing broke. Pushed up & pried out from bottom with same result. Used 1” wood chisel/screwdriver to pry from sides. Finally ‘popped out.’ (Note-Use painter tape to protect finish)Removed old/installed new Electronic Control Board. Put busted housing back in door. It’s working.

Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed

I removed the screws and replace the broken slide with the new slide. Put the basket drawer back on the track and it now stays in place and can easily be used once again.

After removing the key from its shipping package I pushed it into the freezer locking slot and turned it to lock and unlock the lid and then removed it. I had no problems with this fix. Of course, I am an older gentleman with a lot of experience in repairs around my house,as well as other houses. I am sure that a less experienced person may have more of problem with this type of "repair".

Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. Works like a champ again!

The left swing hinge (297283901) that i needed is not available anywhere so I bought the right swing hinge (297283900), used a hydraulic press to pop out the pin and move it to the other hole. After that it was real quick to remove the screws and change out the hinge, changing the swing of the door. It is easiest to remove the top hinge and door first when doing this.

removed old broken part, 3 screws, then installed new part.....done

Remove shelves. Unplug unit. Unscrew back panel. Remove wire harness. Remove old fan. Insert new fan. Screw it in. Reattach wires harness. Plug unit in and make sure fan is on.
Reattach back panel. Put shelves back in.

Removed the basket. Removed the two broken brackets (6 screws). Installed the two new brackets. Put the basket on the track. Done.

Took off cover, unplugged wires, removed old motor, mounted new motor, remounted new motor and replaced cover.

Now need a new control board for same model.

1st Turn off power. Removed freezer racks. Removed access panel to bottom back of freezer. Disconnect the wire harness to fan motor. Use 5/16 nut driver for removing fan motor from support. Removed fan blade from motor and put fan blade on the new fan motor. Bought new fan blades, but new fan blade would not work on new motor. Spring mount would fit on new fan blades, so I use the old one. Installed everything in reverse. Put everything back. Place thermometer in freezer. Freezer cooled down to -10F in 10 minutes. Great save on this one because I bought this freezer off of Facebook marketplace. Saved me $250. Good thing I know about fixing refrigeration equipment. Easy day.

No repair. The key fit!

It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!