LFID2426TF5A Frigidaire Dishwasher - Instructions

I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.

New one snaps into place easily.

Removed the clamp holding it to the floor and
removed the c-clips holding element underneath
and put new one in. Hard part was figuring out
what was holding the element but since I still
had the schematic drawing we figured it out.
Saved a bunch on a repairman. After watching
my friend install the new element I could probably
do it myself next time.

Under sink: Disconnected drain hose to garbage disposal, shutoff water feed, unplugged power.
Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
Removed 3 torx screws on pump, greased o-ring on new pump and reinstalled doing the reverse of these instructions.
Took 1 hour and now it works great!

Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks

FRIDGEADAIRE - GALAXY SERIES -Part arrived within 3 days of order BUT it was wrong part. All excited about getting the upper wash rack in full operation once again. Pilled shelf out to remove gasket to find it looked nothing like the one on there. The part I need is like a bellows of sorts that fits on the water line attached to the upper shelf. The part received goes on the back wall.
Now i am back at square one with part I don't need and hoping for the part I do need

Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.

Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)

Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.

Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.

Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks

We easily removed the original sprayer arm, and clicked the new sprayer arm right into place. I know *very little* about appliances/repairs, etc but this was so easy and an affordable repair for our dishwasher.

The door seal comes off easy. No need to take apart the door. The new seal fits snug. Make sure the notch on the right side of the door seal is installed to the right side of the bottom of door

I took the bottom parts out. This can basically be done without tools. You need a phillips to unscrew 3 screws to remove the stem. Then easily replace with the new one. Putting the spiny washing part was kinda weird because I was afraid to break the nubs off again. I took the whole bottom carriage out so I could see better, pushed down kinda hard and twisted the right way (figure out which way needs to be twisted before hand by looking through the bottom of the stem).

Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

Replaced drain pump. It helped some but still hear some squealing. I suspect the main pump might be worn as well. The drain pump did have some "looseness" to it compared to the new part.

Remove the lower dish tray and set aside. Remove two Phillips screws on each side of inner liner, then close door. You should then be able to slip off the external facing (set aside). Pull lower gasket toward tub until fully removed. Reinsert the new gasket into the same tight slot, making sure that the notch inserts into the slot and the flexible gasket runs the full length of the tub. The gasket should bow out slightly toward the tub. Also make sure that the side seals do not interfere with the bottom seal fully mating with the floor of the tub. Close the door and check to make sure the lower gasket reveal is the same across the length of the inner liner. Reinstall the dish tray, then reinstall the external facing, using the same four Phillips screws to secure. Test sealing by running a short cycle on the dishwasher.

I removed the bottom front of the unit, removed broken friction cable, hooked the new friction cable to the door, attached the cable to the spring, then reattached the spring in the hole provided in the back frane of the unit... Dissappointing how cheaply made these parts are, the dishwasher is just over 1 year old, these friction cables should be made to last longer....