LD10D - Instructions

Replaced diode works great. your website said 92% diode was problem and it worked. Order fuse in case old was blown did not have to use it.

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Make sure to have your model number correct. First tray I purchased I didn't use the model number and just picked what I thought would work (KitchenAid), but didn't. Second attempt I put in the model number and received the correct one. Take out of the box and into the oven, that easy.

Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

I disconnected the power. Took off the front panel that was held together by two screws. Reviewed the schematic that was inside. Located the switches, saw which lead was burnt. Unscrewed the two screws that held the switch in place, cleaned the connector, and put the switch in and connectors back. Powered the device, tested for cooking/heating functionality. It worked, Closed the front panel

Removed case,
Discharged HV capacitor and removed cooling fan.
Unscrewed ground end of HV diode and unplugged from HV capacitor.
Installed new diode by reversing the order. In my case, the problem was the magnetron was bad, so I replaced it as well.

Unplug microwave! It's NOT necessary to remove microwave from above stove. Removed two Philips head screws on top front of unit to remove front grille. Removed one screw to remove control panel, letting it hang down. Found inline fuse in cabinet where line cord wires come in. Pulled out blown fuse with thumb and forefinger. Snapped in new fuse, replaced control panel and grille with the three screws. Plugged in the microwave. -Worked great! Good opportunity while grille was off to clean it and replace the charcoal filter inside the cabinet.

Initially we started looking to buy a replacement microwave to replace our 13+ year old built-in microwave. It was a real pain finding a replacement to fit the exact dimensions. So I thought I'd try to find an old KitchenAid microwave. However, I was pleasantly surprised when this site came up on my search. Their website allows me to input the problems and then it showed two possible parts that needed to be replaced. I emailed tech support and asked them which part I needed. They responded very quickly and said I needed to replace the magnetron. I watched a couple YouTube videos and then pulled my microwave apart. It was incredibly easy to pull the outer cover off. The magnetron had 5 screws that needed to be removed and one electrical plug. Took me maybe 10 min to complete the entire repair. It was one of the easiest repairs I've done and so thankful for this site They saved me a ton of money from not buying a new microwave and we now have our microwave working again. In hindsight, I wouldn't hesitate. I'd order the Part now and get it fixed.

Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.

Opened Box and Replaced Part......No Problem!

The power on the microwave went completely out when I went to use it, but there was no power failure for the house or neighborhood. We removed the microwave from above the oven. Took out the screws on the sides and back of the microwave and slid the top back. The line fuse was located on top unobstructed, NOT behind the button panel like some microwave models. As the appliance is over 20 years old the line fuse was quite old. It was really hard to pry it out of its holder and actually broke. I used a vacuum to suck up the dust and glass and it was easier to get out the ends once the middle broke. Popped the new line fuse in, slid the top back on, put in the screws and put the microwave back in its compartment above the stove. Good as new!! We were about to spend money on a new microwave, but thankfully I came across this site. So happy I did!!

This repair was really easy. The part that took the most time was taking it down from it's compartment above the oven and putting it back up there once repaired.

Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!

ordered a new tray