LAT3600AAE Maytag Washer - Instructions

Tried the water level control first. didn't fix it.
Then replaced the air tube for tub fill volume.

The thing here is that it didn't have a hole in it nor was it blocked where you couldn't blow through it.
The prolbem was that at the tub end it has a larger diameter and that was nearly filled with softener residue so it changed the air volume.
That reduced air volume caused the air pressure to be wrong to the water level sensor.
My most useful tool was a magnet mount flashligt inside the cabinet so I could see to get the hose back on.

First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixed to your machine where you can lift the lid and it will stay up without falling.

Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.

Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck

I checked out the reason why it was not providing hot water then went to this site and found out that it was most likely a water intake valve. I am hardly a do-it-yourselfer, but after watching the "how to" video, I figured why not? The valve arrived in two days, and it was quite easy to do. We now have hot water again.

The instructions were clear. Did every step. Did 2 loads so far and everything works like new.

It was as simple as leaning the machine back far enough so I could get to the belts - which were on the bottom. The diagrams that came with the ordered parts were right on. This is the first time I have attempted this myself - my repairman has retired - I'm sure I will do it again.

Frist remover the two screws from washer front. The ones that are about 5 inches from the floor. Pulled front cover toward me and removed. The hose was right in the front that was cracked. It was held on by two hose clamps. I just removed the old and put in the new. No more water on the floor. Shipping was fast for the hose too. They said that if they recieved the order by 3pm it would be shipped the same day. I order at 3:01pm Sat. recieved Tuesday.

Unplug the washing machine , disconnect the water hoses, and remove two screws. Then remove the bracket and valve from its area. Remove the electrical connections and the small hose, and then reverse the procedures with the new water valve.Plug the washing machine electrical cord in , and hopefully savor the positive results.

One of the easiest repairs I have done to this machine. I took off the back plate of the control panel (the machine was already unplugged) disconnected the connection, removed the old switch and replaced it with the new one. Once all that was done I connected the wires, screwed the back plate back on, plugged it in and started doing laundry.

The End.

Since the washer is 28 years old, my first impulse was to rush out and buy a new one. However, I'm a DYI'er and I figured what do I have to loose by taking the front panel off (I had seen this done by the Maytag Repairman) and checking things out. After removing the two screws located near the bottom front of the panel, I pulled out on the bottom and the panel easily came off. I couldn't see any evidence of leaking water so I thought, "what would the Maytag Man do next". I figured "he'd run through a cycle to see if he could find the leak" so that's what I did. Sure enough, as soon as the spin and drain cycle came on, the source of the leak became apparent. There is a slight vibration during the spin which caused the hose to fail.

I then got on my computer, Googles "repair parts for Maytag Washer" and found Parts Select.Com. I was surprised (to say the least) to find the part I needed in stock. I place my order on Sunday morning and the part was delivered the following Wednesday afternoon. I installed the hose and replaced the front panel and was washing a load of jeans within 20 minutes.

I appreciate the service provided by Parts Select and will be ordering again when the need arises.

Tom Nelson
Fort Worth, TX

Very Easy Repair! Removed 2 screws at the bottom using a philips screw driver(one on each side). Lifted the cover up to detach. 2 screws at the top were removed using a socket set (one on each side). Old tub cover snapped off easily. Make sure you set the cover the same way as the old cover. The new cover snapped on with minimal force. Make sure it's fully seated. Put everything back together in reverse. Took 20min. Most of the time searching for the tools.

I used two vise grip wrenches in place of specialized tool that is no longer available. I put the vice grip wrenches on the brake assembly and hit them alternately with a hammer. I also used penetrating oil.

Note, the parts package stated made in USA but the bearings had China stamped on them.

Removed the front panel. Then blocked up the front of the machine. Removed the pump belt. Removed the 3 5/16" screws from the bottom of the old one and tilted it slightly to remove. Put the new one in and reinstalled the 3 screws. Put the belt back on and slid new pump all the way to the right and tightened 1 screw. Loosened the screw until there was about 1/4" of gap when squeezed the belt together. Tightened the one screw, then the other 2. Put the front panel back on and lowered the machine. New pump works great.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.