LAT2600AAE Maytag Washer - Instructions

Frist remover the two screws from washer front. The ones that are about 5 inches from the floor. Pulled front cover toward me and removed. The hose was right in the front that was cracked. It was held on by two hose clamps. I just removed the old and put in the new. No more water on the floor. Shipping was fast for the hose too. They said that if they recieved the order by 3pm it would be shipped the same day. I order at 3:01pm Sat. recieved Tuesday.

Unplug the washing machine , disconnect the water hoses, and remove two screws. Then remove the bracket and valve from its area. Remove the electrical connections and the small hose, and then reverse the procedures with the new water valve.Plug the washing machine electrical cord in , and hopefully savor the positive results.

One of the easiest repairs I have done to this machine. I took off the back plate of the control panel (the machine was already unplugged) disconnected the connection, removed the old switch and replaced it with the new one. Once all that was done I connected the wires, screwed the back plate back on, plugged it in and started doing laundry.

The End.

The instructions were clear. Did every step. Did 2 loads so far and everything works like new.

I went to the Internet and saw how to pry the front panel off the washer. This gave me access to the two belts and four pulleys underneath the washer; a pair for the Drive and a pair for the Pump. There was enough slack in the original belts that they came off with minimal effort. The new belts were easy enough to install. It took a mere seconds to install the new Spacers on the Front panel of the cabinet. The most time consuming portion of the project was getting the washer turned out of its tight corner to get access to the clips on the bottom of the front panel.

Called 800 number to make sure I had right part. There were two series and she was very helpful. Ordered Thursday after business hours and received by standard delivery on saturday. Unscrewed 5 screws. Unplugged two plugs on switch and two more screws. Plugged new switch in and had working like new in 15 minutes. Very pleased.

Since the washer is 28 years old, my first impulse was to rush out and buy a new one. However, I'm a DYI'er and I figured what do I have to loose by taking the front panel off (I had seen this done by the Maytag Repairman) and checking things out. After removing the two screws located near the bottom front of the panel, I pulled out on the bottom and the panel easily came off. I couldn't see any evidence of leaking water so I thought, "what would the Maytag Man do next". I figured "he'd run through a cycle to see if he could find the leak" so that's what I did. Sure enough, as soon as the spin and drain cycle came on, the source of the leak became apparent. There is a slight vibration during the spin which caused the hose to fail.

I then got on my computer, Googles "repair parts for Maytag Washer" and found Parts Select.Com. I was surprised (to say the least) to find the part I needed in stock. I place my order on Sunday morning and the part was delivered the following Wednesday afternoon. I installed the hose and replaced the front panel and was washing a load of jeans within 20 minutes.

I appreciate the service provided by Parts Select and will be ordering again when the need arises.

Tom Nelson
Fort Worth, TX

Very Easy Repair! Removed 2 screws at the bottom using a philips screw driver(one on each side). Lifted the cover up to detach. 2 screws at the top were removed using a socket set (one on each side). Old tub cover snapped off easily. Make sure you set the cover the same way as the old cover. The new cover snapped on with minimal force. Make sure it's fully seated. Put everything back together in reverse. Took 20min. Most of the time searching for the tools.

I used two vise grip wrenches in place of specialized tool that is no longer available. I put the vice grip wrenches on the brake assembly and hit them alternately with a hammer. I also used penetrating oil.

Note, the parts package stated made in USA but the bearings had China stamped on them.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

Removed the front panel. Then blocked up the front of the machine. Removed the pump belt. Removed the 3 5/16" screws from the bottom of the old one and tilted it slightly to remove. Put the new one in and reinstalled the 3 screws. Put the belt back on and slid new pump all the way to the right and tightened 1 screw. Loosened the screw until there was about 1/4" of gap when squeezed the belt together. Tightened the one screw, then the other 2. Put the front panel back on and lowered the machine. New pump works great.

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

Washer originally purchased from Sears. Called Sears for repair. $65.00 to show up. Diagnosed the problem as a Bad belt and pump. Asked for approx. $250 to repair. I declined and ordered a belt and pump from PartSelect.com for half the cost. Took 10-15 minutes to install. Turned the washer on and put it through a drain cycle, it leaked all over the floor. Turns out the only problem was a cracked Outer Tub to Pump Hose. It took about 10 minutes to install. Whala, no leak. Now while I purchased an un-needed pump and belt from PartSelect.com, not their problem. Even though I purchased two items that were not required, the cost was still half of what Sears wanted to charge me for a repair that would not have fixed the problem. I will certainly continue to use and recommend PartSelect.com.

After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.

Removed top. Removed agitator and tubs . Replaced seals and reassembled.