LA600AXD2 Frigidaire Washer - Instructions

The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning properly. Having to make a new mounting plate was an unexpected adventure!

watched the video, all instructions were perfect!

Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off

Used flat head screw driver to pry up the top. Removed front cover. Pushed tension idler pulley back to release tension on the belt. Removed old belt. Put new belt on motor pulley and idler pulley. Started one edge on main pulley and slowly rotated main pulley until the belt popped in place. Tested on spin cycle. Replaced front cover and top. Unfortunately, this didn't stop the noise...turned out a shipping screw was still in place. Removed the shipping screw and voila! no noise. It's always the little things that get ya.

Quick google search brought me to this site, part was very easy to locate and purchase. The part was delivered within 5 days and 2 screws, 2 wires, 2 hoses, and 15 minutes later it was a done deal.

lifed the lid .remove oud hose and replaced with new hose

Took front off and put the new belt on. Then put the front back on. At my Age 70 yrs did good and saved $124.00 Which I paid that 9 months ago.

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

This repair couldn't have been easier. I went to the website, looked up my part and ordered it - this all took longer than the repair! I followed the super easy video on the site walking me through the replacement step by step. I probably would have taken less time, but I made the mistake of propping the top of the washing machine up too high, which popped a suction hose that prevents the tub from overfilling, which unfortunately, I didn't realize. 10 minutes, I started to do a small test load. Luckily, our laundry is right off of the kitchen, so after 5 minutes of filling, I stopped eating dinner to ask my wife how long it took to fill. At that, we could hear the water running on to the laundry room floor. Another trip to the internet and sure enough, attaching that hose fixed her right up. Thanks Partselect! Couldn't have made my life easier - much to the chagrin of my wife who was searching feverishly through the paper for a replacement!

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

I used this website to look at the parts breakdown the only way water can get into the machine is thru the solenoid valve. Ordered valve.Followed the video on how to replace valve.I pulled apart the old valve. The plastic seat was cracked,letting water seep into the machine.

released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.

Changed the belt started working like new.

did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.

Watched the handy-dandy video, removed the defective part, waited for delivery, installed the new part and was back washing another load (minus the wet floor) in less than 10 minutes! Just one catch, I am a 56yo female with nominal hand strength, so technically, I had to recruit the help of a (stronger) person to tighten-up those self-tapping screws. I didn't feel so weak when I noticed that he had some difficulty as well. LOL! Ladies, don't be shy asking for help-I even tried the power drill with no success. Excellent video! Aside from the self-tapping screws, my grand-daughter could have managed this repair!