KUIP15PRXX0 KitchenAid Ice Maker - Instructions

I've tried ordering the part from Sears and they told me it will take about 7 days for the part to arrive, some other place said it will overnite for extra money. So I've ordered the part from Part Select at a good price and prompt delivery. once the part arrive installing the part so so easy cause it had easy to follow instructions.

Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.

Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.

A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

Pretty much followed the how to video. Biggest pain was removing the screws to the bracket that houses the motor.

Fast after a little help from a friend

I called the 800 number and the lady was great to work with and helped me thru all the order process and confirmed the numbers. She also told me she would try to get the order out that day which she did and I had the part two days later. When it arrived I went to the web site and reviewed the video and went to work and all went as the video said. Thanks for the help and if i need another part I will visit your site or call.

I watched the film on installing and taking out. Step by step. easy.

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.

Instructions were really clear and easy to follow. Hardest part of the job was moving the refrigerator away from wall after it was filled with holiday groceries.

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

Removed old assembly by disconnecting 2 wiring harness connections and loosening 2 screws with nutdriver. Installed new assembly using same process. Had ice in about an hour. Very easy.