KUDA22SWWH0 KitchenAid Dishwasher - Instructions

The tube had holes from being used but the dishwasher still works great. I researched this part and it was a great price and really easy to fix. The picture looks different than what the tube looks like in the dishwasher but it is correct. Definitely put soap on the ends to help glide it on. Took me 2 minutes to fix.

simply pieced together the "tube"

I was trying to avoid having to buy a new dishwasher before the holidays. I went on YouTube and found the dirty dishes may mean bad water inlet valve. So, I used my meter to see if the valve was bad and sure enough it was. I ordered the part from Part Select. Once I received the part I removed the old one. Be sure to put a towel down to catch the excess water. The bracket that came with the new prt was a different configuration, but i swapped the new with old and it worked. I addition to the valve being bad the dishwasher upper and lower arms were somewhat clogged. I looked online again and followed YouTube instructions to clean. The dishwasher is cleaning like it is new. I would recommend to anyone doing work on their dishwasher to use part select and thoroughly clean the upper and lower arm.

After checking for blockages in the drain line and finding none, I disassembled the wash wand assembly and discovered a gasket that had really deteriorated. Since there was nothing else apparently wrong, I took a chance and went shopping for the gasket. None of my local stores could provided me one so I searched on line and found it at Partselect. It had to be special ordered and that took a while, but when it arrived, I put the new gasket in and had a perfect dishwasher again for less than 15 bucks. The schematic I was able to print from your website was invaluable.

First the water tube arrived two days earlier than what I was expecting. I pulled the old tube off and slipped the new tube on by hand. The dishes in the top rack are now a lot cleaner than they have been for the past couple of months. In the future if I need repair parts this is where I will be coming to get them.

just popped the old hose off and put the new one on. the part was shipped very quickly and I received it within a week even during the holidays

Removed old tube, moistened both ends of new tube with hot water and slid over inlet and outlet holes. Repair done!

I removed clips on the end of the rack, removed the rack, and pulled old tube off. Used plain water as a lubricant to ease replacement of new tube on the dilated end. Very easy!

Warm rollers and holders in warm water for 2 min each slide on all done

slid old tube pieces off slid new hose on

The replacement worked fine, but the website could have been a bit more re-assuring in terms of showing the image of the part. It was not possible on the website to determine whether the piece was going to fit, as the piece as shown was flat/oval on both ends, where the fitting for the water feed is round. The site could have explained that this was flexible material that would form itself to the round feed connection. The measurements of the part should also be given. The price was right, so I bought it anyway, and hoped. As I have said, it DID work fine. You need to clarify the item on the website.

Replaced the tube. It was relatively easy although it did take a small bit of squeezing/reshaping the newer rubber tubing to get it to fit on the outlet (it was a bit snug.)

I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.

One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!

Removed the old part. It came out with no problem
due to being brittle and cracked. This part was original to my 15 1/2 year old dishwasher.

Ran hot tap water in the sink and soaked the new "Rubber Water Delivery Tube" for about 5 min. I put a little dish washing liquid on dishwasher part where tube was to be slid onto. Including the soaking time,repair took less than 5 1/2 min.

I'm very pleased by the fact that my part arrived in a little over 1 1/2 days.

Was lucky the part was available. I put liquid detergent on both ends of tube, then slid each end onto each sleeve. Works great now!