KSM85PSQGC0 Whirlpool Mixer - Instructions

unscrewed the screw holding the old brush. carefully removed the spring and old broken brush. we did have some of the old brush left inside, so my husband used a very thin drill bit to break it up. then carefully inverted the stand mixer to allow the broken pieces to fall out. then we were able to install the new brush. works great. yeah!!

Took the old feet (5) off and put new on the Kitchen Aide, looks great. Stands high and your assistance on the phone, was so appreciated.

first removed the dress ring by tapping it very gently.then drive the pin out that holds the beater plate on, now wiggle it off, then you can see the screws that hold the gear reducer on. remove them. take that off and you will see the housing that hold the worm gear. remove the 3 screws that hold it down . Now you will have to drive the drift pin out that holds the worm gear in place, slide the shaft out then remove gear. reverse order to assemble

My early '60's Kitchenaid K45 mixer screw cap/base plate would no longer hold the bowl, so I looked for another. This item, though not an exact replica of the original, fit and works great. The design is better by being more stout than the original. Pretty straightforward installation: remove three screws, take out old base plate, install new plate and screw down.

Very messy as there is lots of heavy grease inside the mixer and you have to fish out the blown gear parts. I vary glad I took shop class in High school as it preped me for the job. The machanical drawing you provide were very useful but you should mention the grease.

Mixer works just like new. and I got the parts in two days with standard shipping. Pizza on Thursday and fixed by Saturday

total replacement
works beautifully

Took the mixer apart and cleaned the grease so off I could see the pins. Wasn't a hard fix only thing is make sure to clean the grease off so you can see what your doing

all that were required, were you take off old beater an replace new.simple push up old part an replace new. as you do after usage of the machine.

All I had to do was insert the new beater. Wonderful timing, was just going to start some holiday baking. will definetly use your website again. Thank you.

Insert and off you go. No real installation.

put new paddle on

‘Can’t remember well enough to describe accurately. Removed one screw to remove rear cover. Removed two screws to remove bright-metal band - probably not necessary but it did yield a bit more working space. IIRC, three screws and removing wires from spade-connectors was sufficient to remove the speed control plate. Remove one more screw to remove phase control board (probably unnecessary). I took close-up pictures with my iPhone first to assure wires would get replaced on the proper lugs (only to discover the wiring diagram later). Adjusting the control plate to meet the speed criteria in the instructions was very easy. It did serve to remind me that I probably didn’t need either of the new parts; readjusting the old speed control plate would probably have done it. But I appreciate the POM brought on by the new parts.

It’s an incredible pleasure to work on something so well-made as this old Kitchen-Aid mixer. I just enjoyed handling it! Having achieved a proper repair was rather satisfying too. I just loved the entire experience!

I called my fiancée.

Followed step-by-step video instructions for dis-assembly/reassembly found at ereplacementparts.com. All went well except when driving out the pin that holds the worm gear in the tower. The video wasn't exactly clear enough about what position the pin should be in when driving it out and I inadvertently drove the pin out so that it was trapped inside the tower assembly. Result? I had to bend the pin to get it out, causing an extra expenditure and wait time to order a new pin. So, lesson learned: be sure the pin is horizontal to the tower and not perpendicular to when driving the pin out. Also, I found that having the mixer apart was a good time to replace the grease in the housing. I don't think it would be required to replace the grease at this time but I was worried that pieces of the old worm gear could remain in the grease and possible get jammed in the gears after repairs were completed. Be sure to get a "food grade" grease not grease from your local auto parts store! The table knife was the best tool to use to remove the grease and to smear the grease all over the internal gears when replacing it.

Just replaced the beater.