All Installation Instructions for Whirlpool Mixer KSM85PSCWH5

mixer wouldnt turn on

watched an internet video to see what to do. Unfortunately even after replacing the chip the mixer it still didn't work.

Parts Used:

Mixer Phase Control Board

marc from MOBRIDGE, SD
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replaced worn out gear

Fairly easy if you have done it once before.

Parts Used:

Worm Gear

Mixer Retaining Pin

Richard from SUQUAMISH, WA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Speed control not working properly

Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.

Parts Used:

Mixer Phase Control Board

Mixer Speed Control Plate

Reid from MONTICELLO, MN
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Wasn’t spin any moore

Follow a YouTube video step by step

Parts Used:

Worm Gear

Rosa from GLOUCESTER, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Cord split in half

I removed one screw on back, once inside mixer I removed the ground screw then pulled off the black and white push on caps, then I reversed everything to get it installed, very easy

Parts Used:

Power Cord

LEONA from PORT ST LUCIE, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old wire whip was broken

Just put on the new whip...exactly like old one.

Parts Used:

Wire Whip Mixer

Stephanie from JACKSON, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Screw cracked on the front of the mixer

Skewer the screw in with my fingers,

Parts Used:

Mixer Thumb Screw

Mrs Brenda from LYNNWOOD, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

bowel would come out of screwcap when making dough for pasta

The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we could keep it going.

Parts Used:

Mixer Screw Cap

Robert from AURORA, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old screw cap wore out and would not hold bowl when mixing heavy batters.

Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.

Parts Used:

Mixer Screw Cap

Sharon from FAIRFIELD, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Base plate destored

I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws

Parts Used:

Mixer Screw Cap

Gordon from West Stockbridge, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Very Happy

Easy

Parts Used:

Wire Whip Mixer

Joel from Mount Clemens, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

no mixing

dis-assemble, replace part, re-lube, reassemble, test good.

Parts Used:

Worm Gear

per from highland, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

The mixer broke the worm gear(the only plastic gear inside the mixer) and needed replaced.

I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new grease for smooth operation, I simply put it back together and it has worked like new ever since.

Parts Used:

Worm Gear

Dustin from JACKSONVILLE, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The original screw cap would not hold the mixer bowl in place anymore.

The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!

Parts Used:

Mixer Screw Cap