KSM192XDPL5 KitchenAid Mixer - Instructions

and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED

Replaced it with a new part. No installation or repair to maching was necessary

Put on a new base plate using fresh screws, all ordered on Parts Select in under a minute. Now my grandmas old Kitchen Aid Stand-up mixer is as good as new! This was way easier than I thought it would be and really a great experience!

Just screwed it in

i followed the instructions in video. Thank you joe

Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.

Followed directions video on line. good directions.

Easy removal of old screw cap, but new one didn't just drop in. Had to scrape paint and a little aluminum to make it fit. Finally did, and it works fine now.

it was a kitchen aid dough mixer, had to take the top portion off and replace the assembly with a new one that holds the teflon gear. You can purchace the gear only and it becomes less expensive, but at the time I didn't take the chance cause the greese was there and didn't want to take a chance. Its a simple repair by removing some cotter pins and phillips head screws.

I how the video for replacing the worm gear on your website. It help me a lot. I followed step by step instruction display on video. It was great help.

Took the mixer down to the gear box. Found the plastic drive gear had a few stripped teeth. Did a search on the internet for the mixer gear. Found a couple of suppliers. Ordered the needed gear, pin and a bearing block just in case it was worn. The bearing block did not need to be replaced. Cleaned the broken off teeth from the gear grease and put the mixer back together. All worked fine when I plugged it in.

I found a video on how to repair mixer that would not turn. Watched video several times and replaced worn worm gear. Getting the old worm gear was the most difficult part of the job. I had to go purchase a pin punch ($5.50) with the correct tool is was easy.

My husband looked at youtube to figure out what the issue was. He saw a video that identified that the likely problem was the worm gear. My husband took the kitchenaid applicance apart, as he saw in the video. We ordered the part, it took less than a week to arrive. He rewatched the video that demonstrated how to put the kitchenaid mixer back together. It's a bit messy due to all the packing grease, but a pair of nitrile gloves, paper towels, and an old rag help. We put a garbage bag over the appliance after it was taken apart to protect it from any dust and my curious cat. We let the kitchenaid cycle for about a minute to make sure the gear was greased. I haven't used it to make bread yet, but I'll do that soon. Thanks for supplying the part that saved us at least one hundred dollars and TRY to get a person who will repair small appliances.

I took out the worm gear and replaced it with the new one. It is important to have the correct punches that are just under the diameter of the pins.

followed the instruction on you tube