All Installation Instructions for KitchenAid Mixer KSM192XDBK0

Pin fell out of neck

Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!

Parts Used:

Tiffany from San Antonio, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Mixer bowl was slipping off the base when in use

Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.

Parts Used:

Mixer Screw Cap

Dean from Fairfax, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Wire Whip was coming apart

Replaced it with a new part. No installation or repair to maching was necessary

Parts Used:

Wire Whip Mixer

Lois from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Plastic worm gear stripped

The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.

Parts Used:

Worm Gear

Pete from Tracy, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

wire whip brokrn

Just screwed it in

Parts Used:

Wire Whip Mixer

Lawrence from Craryville, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Lost a rubber foot on my Kitchen Aid mixer. The remaining feet we're hard and mushroomed. I decided to replace all 5. That was the correct decision.

I griped each foot with a pliers and twisted it out of its setting. I then set a new foot in place and hammered it into place with a small hammer. The feet fit snugly and did not need to be glued. Job was easy and mixer sits like new. I was glad I spent the money to replace all of the feet at once.

Parts Used:

Blender Foot

Dale from Manheim, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Brush's Wore

Change brush's

Parts Used:

Mixer Motor Brush

Gary from Scottsburg, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

would not run

I just put in the new brushes

Parts Used:

Mixer Motor Brush

INSERT - BRUSH HOLDER

andrew from bridgeville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Motor would not turn on

Initially removed carbon brushes then inserted the new carbon brushes. The motor still did not turn on. Then I removed the brushes again, used a flashlight to look in the hole where the carbon brushes are installed. I noticed that there was a square notch on one side of the hole. I then reinstalled the carbon brushes, ensuring that the beveled side of the carbon brush was installed so it lines up with the square notch. This allows the carbon brushes to touch the motor. I turned the unit on and it worked.

Parts Used:

Mixer Motor Brush

Paul from Reno, NV
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Bent wires in a wire whip

I ordered a new wire whip and attached it just like it was the original. WALLA!!! Done.

Parts Used:

Wire Whip Mixer

Robert from Blairsville, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The screw cap no longer held the bowl in place.

This is the easiest repair ever! I removed the 3 screws, cleaned around the area with a sponge and kitchen cleaner and put on the new cap. The screws went back in easily and voila ! Done!

Parts Used:

Mixer Screw Cap

Roberta from Glen Ellyn, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

original part worn out, wouldn't hold mixing bowl

unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.

Parts Used:

Mixer Screw Cap