KSM180LELB0 KitchenAid Mixer - Instructions

The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.

Put on a new base plate using fresh screws, all ordered on Parts Select in under a minute. Now my grandmas old Kitchen Aid Stand-up mixer is as good as new! This was way easier than I thought it would be and really a great experience!

it was a kitchen aid dough mixer, had to take the top portion off and replace the assembly with a new one that holds the teflon gear. You can purchace the gear only and it becomes less expensive, but at the time I didn't take the chance cause the greese was there and didn't want to take a chance. Its a simple repair by removing some cotter pins and phillips head screws.

I how the video for replacing the worm gear on your website. It help me a lot. I followed step by step instruction display on video. It was great help.

I took out the worm gear and replaced it with the new one. It is important to have the correct punches that are just under the diameter of the pins.

My husband looked at youtube to figure out what the issue was. He saw a video that identified that the likely problem was the worm gear. My husband took the kitchenaid applicance apart, as he saw in the video. We ordered the part, it took less than a week to arrive. He rewatched the video that demonstrated how to put the kitchenaid mixer back together. It's a bit messy due to all the packing grease, but a pair of nitrile gloves, paper towels, and an old rag help. We put a garbage bag over the appliance after it was taken apart to protect it from any dust and my curious cat. We let the kitchenaid cycle for about a minute to make sure the gear was greased. I haven't used it to make bread yet, but I'll do that soon. Thanks for supplying the part that saved us at least one hundred dollars and TRY to get a person who will repair small appliances.

followed the instruction on you tube

Followed directions video on line. good directions.

The brushes on the inside of the motor were destroyed. We thought that it would be easier to just replace the brush holder and the brushes, however, the brushes were easy! and QUICK! The brush holders...not so much. We had lots of problems getting the brush holders into place because of a metal piece that had to fit perfectly on top of the brush holder. It made it easier when I held the mixer upside down (we dissembled it) and my husband did his magic on fixing the brush holders. Pray that you won't need to replace the brush holders because it was NO FUN...but the brushes were QUICK AND EASY :)

Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.

i followed the instructions in video. Thank you joe

Took the mixer down to the gear box. Found the plastic drive gear had a few stripped teeth. Did a search on the internet for the mixer gear. Found a couple of suppliers. Ordered the needed gear, pin and a bearing block just in case it was worn. The bearing block did not need to be replaced. Cleaned the broken off teeth from the gear grease and put the mixer back together. All worked fine when I plugged it in.

I found a video on how to repair mixer that would not turn. Watched video several times and replaced worn worm gear. Getting the old worm gear was the most difficult part of the job. I had to go purchase a pin punch ($5.50) with the correct tool is was easy.

After I dropped a part of the shield into my mixer the motor screamed and I unplugged the mixer. I found out I had a broken worm gear. I then order the part and per the helpful video I did the repair and I also changed the brushes my mixer is up and running waiting for the holiday baking season thanks to Part select.com Very easy Instructions to follow I am very happy with the results. Thanks Barbara

I discovered the brushes were worn, and one side had broken off and lodged against the armature.I got lucky as I removed the brush caps and the sleeves the brushes fit into (simple job) and was able to hand turn the armature so the pieces fell down into the bottom of the mixer housing.After removing them, I replaced the brushes and the mixer runs like new. Thanks for the fast delivery AND more importantly, the right part. Steve