Models > KSM180CBLD0 > Instructions

KSM180CBLD0 Whirlpool Mixer - Instructions

All Instructions for the KSM180CBLD0
121 - 135 of 161
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The screw cap no longer held the bowl in place.
This is the easiest repair ever! I removed the 3 screws, cleaned around the area with a sponge and kitchen cleaner and put on the new cap. The screws went back in easily and voila ! Done!
Parts Used:
Mixer Screw Cap
  • Roberta from Glen Ellyn, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
head of screw was broken in half
I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie
Parts Used:
Mixer Thumb Screw
  • marjorie from juda, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
original part worn out, wouldn't hold mixing bowl
unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.
Parts Used:
Mixer Screw Cap
  • Diane from Holland, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The thumb screw plastic came off
Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.
Parts Used:
Mixer Thumb Screw
  • Karen from Salem, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lost a rubber foot on my Kitchen Aid mixer. The remaining feet we're hard and mushroomed. I decided to replace all 5. That was the correct decision.
I griped each foot with a pliers and twisted it out of its setting. I then set a new foot in place and hammered it into place with a small hammer. The feet fit snugly and did not need to be glued. Job was easy and mixer sits like new. I was glad I spent the money to replace all of the feet at once.
Parts Used:
Blender Foot
  • Dale from Manheim, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
I had lost the thumb screw
I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.
Parts Used:
Mixer Thumb Screw
  • Jane from Crivitz, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken Part to KitchenAid Mixer
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again
Parts Used:
Mixer Thumb Screw
  • PJ from Rome, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Brush's Wore
Change brush's
Parts Used:
Mixer Motor Brush
  • Gary from Scottsburg, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
would not run
I just put in the new brushes
Parts Used:
Mixer Motor Brush INSERT - BRUSH HOLDER
  • andrew from bridgeville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
needed new brushes for a mixer
Easy to locate part I needed (brushes)..great diagrams Thanks
Parts Used:
Cap Spring
  • Linda from St. Cloud, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Food mixer suddenly stopped without burnning smell
Just change the motor brush. That's it! It work well now. Thank you, Partselect!
Parts Used:
Mixer Motor Brush
  • Takahiro from Arlington, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Screw cap or retainer wore out and wouldn't hold the bowl tight
Removed the old screw cap and installed the new one-only has 3 screw to remove and re install. VERY easy. Fits perfectly
Parts Used:
Mixer Screw Cap
  • Robert from Aitkin, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Sticky back disc on Orbital sander came apart (from old age )
remove 3 screws ,remove old sanding disc replace with new installl screws
Parts Used:
Worm Gear
  • David from Tolland, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The worm gear driven by the motor stripped due to excessive load.
Remove the mixer head from the base by removing the 4 Phillips head screws. Pry off the ring around the rotating part with a flat head screwdriver. Punch out the pin holding the rotating part and remove. Remove the trim strip by removing the two Phillips screws at the rear of the unit. Remove the 4 screws at the bottom of the mixer head. Carefully separate the bottom of the head from the top using a flat screw driver. There will be the power wires connecting the top to the bottom of the unit. It is best to disconnect these wires to avoid breaking them during rest of the procedure. There will be a lot of grease in the gear box of the mixer. The assembly holding the damaged worm gear can now be removed by removing the three screws holding it to the bottom of the mixer head. At this point I removed the grease from the worm gear assembly to allow better inspection. Punch out the pin holding the worm gear to its shaft and remove the shaft. The worm gear is now free and can be replaced. Add some extra grease to the new gear and reassemble the mixer in the reverse order.
Parts Used:
Worm Gear
  • James from Central City, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
worm gear had broken tooth and gear was loose on sprocket
I dismantled the machine to find the problem and to see what part I needed. Than when I ordered the part I saw the video of how to do it. If I had seen the video before I dismantled, I would have save a few steps. The video was very complete and accurate even it being an older model
Parts Used:
Mixer Worm Gear & Bracket
  • Larry from Briggsdale, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KSM180CBLD0
121 - 135 of 161