KSM150PSLR5 KitchenAid Mixer - Instructions

INSTALLED PHASE CONTROL BOARD AND SPEED CONTROL PLATE, BOTH AT SAME TIME
Your DYI video was helpful, especially holding the spring with a cloth. Also good for fine tuning to get the speed exact

Took each area apart. Replaced the gear and reassembled it.

Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!

I watched a YouTube video all the way through, then watched each segment and followed along with the video. It was messier than the professional repair guy, but it worked out fine. This is not a difficult repair when you can watch a video and follow along. It saved me about $130.

I replaced the phase control board because the mixer had only
one speed and was surging. I noticed from other posts that it
is important to note the setting of the speed plate before you
remove it in order to remove the phase control board. Also be
careful removing the associated 'slip-on' terminals as it would
be easy to damage the speed plate. If I ever do this again I
will go ahead and replace the speed plate, probably the cheapest
item to replace. The operation was a success and the mixer is
back in business. Thanks.

You tube has great instructions! I would suggest when you buy a part to let customer know that they need a food grade gear grease ordered to complete the reinstall of all gears and body parts!

Dismantled the mixer, took photos, and re-assembled unit.

I watched the university of YouTube videos, and followed their instructions.

I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was very reasonable

Followed your instructions from the internet and it was a simple fix. Mixer works great again. Thank You ..you made it easy!

I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new grease for smooth operation, I simply put it back together and it has worked like new ever since.

The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!

Removed back cover, disconnected the 2 push-on connectors, removed ground wire screw. Reversed the process to install new cord.

had to replace the outlet strip and relocate the mounting screw,,,,wiring cord to the mixer was super correct and had to simply follow basic wiring (black to black,,,silver to silver,,,green to ground) ,,, the cord came with the correct mounting bushing already on the cord. Thx a bunch!

I had a sourdough batch get into the space where dough hook attaches and it got so stuck that nothing - not hot water baths, not pliers and screwdrivers got the dough hook released. I had to open up the mixer following partselect you tube instructions and replacing the parts. What was confusing to me at first is that my 45 year old mixer had an extra screw on top of the shaft that no longer is there for newer models. It took me longer than I am willing to admit to figure that the extra screw is not the result of me skimming the instructions - the original shaft and dough hook went to a friend who broke it attempting to disengage the two parts (the dough turned out to be a very strong form of glue!). The piece is working like new. I preferred the agitator shaft with a spring to hold the end piece tighter, but the new set up without a spring works just fine.