Models > KSM150PSGR5 > Instructions

KSM150PSGR5 KitchenAid Mixer - Instructions

All Instructions for the KSM150PSGR5
31 - 45 of 168
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Missing pedestal foot
Turned the mixer on its side and slid the part into the bottom of the base.
Parts Used:
Blender Foot
  • Michael from CARLISLE, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Kitchenaid has bad white coated beaters that peal off
None
Parts Used:
Mixer Flat Beater
  • Darlene from North Liberty, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace base plate on KitchenAid mixer
Took out 3 screws, removed old plate, put down new plate the tightened screws. Runs like new, great service, price, quick delivery!
Parts Used:
Mixer Screw Cap
  • Joyce from Great Bend, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worm gear broken
I called my fiancée.
Parts Used:
Worm Gear
  • Jennife from Lancaster, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed new flat beater
Just replaced the beater.
Parts Used:
Mixer Flat Beater
  • Juanita from Ferndale, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When using the bread hook, the force of the dough would knock the bowl out of the retaining ring on the mixer (Cap-Screw.)
Three phillips-head screws held the "Cap Screw" in place on the stand of the mixer. After cleaning the stuff out of the screw slots, the screws came out surprisingly easy. After the plate was lifted off, we cleaned the residue from under the plate, placed the new one in position and easily screwed in the 3 screws.
We were very pleased by the quick delivery of the part.
Parts Used:
Mixer Screw Cap
  • Jerry from Burnsville, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pin was missing on mixer allowing head to move.
Inserted new pin and tightened set screw.
Parts Used:
Mixer Dowel Pin
  • James from Columbus, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
11 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
mixer would not turn
removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.
Parts Used:
Worm Gear Mixer Retaining Pin
  • James from Wewahitchka, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
use your phones to take pic of how the wiring is to be reconnected, take pleanty from all angles
repair is farly simple just take your time, First attempted i didnt replace the speed covernor looked ok but had problems getting slow end to work properly decided to go ahead and install since i purchased it also and walia took care of the cogging problem. Good Luck
Parts Used:
Speed Governor Mixer Phase Control Board Mixer Speed Control Plate
  • Douglas from FREEPORT, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic boke on the old thumb screw
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!
Parts Used:
Mixer Thumb Screw
  • Alice from St Louis, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer bowl that came with the 5 quart mixer would not lock on the base
New mixer bowl locks
Parts Used:
BOWL-MIXER
  • Michael from SACRAMENTO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pin was missing therefore no mixing function
Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom
Parts Used:
Mixer Retaining Pin
  • Thomas from COLUMBIA, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer stop rotating
Replace went good used the online video, my husband doesn't usually use any help but said the video helped him. Now my mixer works perfect. Also the price and shipping time was awesome.
Parts Used:
Mixer Flat Beater Mixer Worm Gear & Bracket
  • Sherriel from TERREBONNE, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed switch wouldn’t stay in off position
Watched a YouTube video to disassemble,from there went smoothly. One small piece of advice,take pictures with your smart phone during the process. Makes remembering easier.
Parts Used:
Speed Link Mixer Speed Control Plate Mixer Speed Control Lever
  • Steven from CUBA, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spent Pevel Pinion Center Gear
remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.
Parts Used:
GEAR-HUB
  • EUGENIO from MIAMI, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KSM150PSGR5
31 - 45 of 168