KSM150FBER0 Whirlpool Mixer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Coating on beater wore off
Simply replaced the beater.Ordering part was simple and delivery was quick. I was back at baking in no time! Great service
Parts Used:
-
Sandra from Jackson, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Food mixer suddenly stopped without burnning smell
Just change the motor brush. That's it! It work well now. Thank you, Partselect!
Parts Used:
-
Takahiro from Arlington, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
needed new brushes for a mixer
-
Linda from St. Cloud, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No repair I purchased a part.
The part fit great! PS. I may need to buy a gasket to go around my refrigerator door. I have an Amana Model #THI1853W, Serial No. 9502301998. Do you have instructions on how to install this gasket?
Parts Used:
-
Ernet from Birmingham, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Motor would not turn on
Initially removed carbon brushes then inserted the new carbon brushes. The motor still did not turn on. Then I removed the brushes again, used a flashlight to look in the hole where the carbon brushes are installed. I noticed that there was a square notch on one side of the hole. I then reinstalled the carbon brushes, ensuring that the beveled side of the carbon brush was installed so it lines up with the square notch. This allows the carbon brushes to touch the motor. I turned the unit on and it worked.
Parts Used:
-
Paul from Reno, NV
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The screw cap no longer held the bowl in place.
This is the easiest repair ever! I removed the 3 screws, cleaned around the area with a sponge and kitchen cleaner and put on the new cap. The screws went back in easily and voila ! Done!
Parts Used:
-
Roberta from Glen Ellyn, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
head of screw was broken in half
I looked on line found the product sent in information and 3 days later was in my mailbox,great service and ease of ordering. thanks marjorie
Parts Used:
-
marjorie from juda, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Bent wires in a wire whip
I ordered a new wire whip and attached it just like it was the original. WALLA!!! Done.
Parts Used:
-
Robert from Blairsville, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Beater was peeling and chipped; thumb screw was worn & loose to the point it would fall out
It only involves reinserting the beater . And the thumb-screw was falling out so I cleaned the area and replaced the thumb screw. Very simple and easily done.
Parts Used:
-
Carol from LIGNITE, ND
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
original part worn out, wouldn't hold mixing bowl
unscrewed old part, put in new part.New part much better design than old one. Works great. Your service is great. Had the part in a 2-3 days. Awesome.
Parts Used:
-
Diane from Holland, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Part to KitchenAid Mixer
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again
Parts Used:
-
PJ from Rome, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lost dough hook so no repair
-
jennie from cupertino, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Coating on original flat beater was cracking.
I just replaced my old flat beater with the new one. It fit and worked perfectly.
Parts Used:
-
Deanna from Saint Joseph, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The thumb screw plastic came off
Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.
Parts Used:
-
Karen from Salem, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lost a rubber foot on my Kitchen Aid mixer. The remaining feet we're hard and mushroomed. I decided to replace all 5. That was the correct decision.
I griped each foot with a pliers and twisted it out of its setting. I then set a new foot in place and hammered it into place with a small hammer. The feet fit snugly and did not need to be glued. Job was easy and mixer sits like new. I was glad I spent the money to replace all of the feet at once.
Parts Used:
-
Dale from Manheim, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!