KSM150APSGD0 KitchenAid Mixer - Instructions

remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.

This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!

no instructions necessary

Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom

I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok

Repairing/replacing worm-gear (FSP part# W10112253) for a KitchenAid Stand Mixer model number K5SS. First: I am writing this story because all the videos or repair articles I’ve viewed are either misleading or incorrect in that they do not include older K5SS models. 1. These older models from the mid 1960’s or even earlier have four very large #4 chrome plated Phillips Head Screws holding the mixer base to the motor assembly and NOT four small machine screws (one with a lock-washer) as seen on other repair videos. In addition, the stand is composed of two separate pieces with the bottom half being held together with another four identical #4 chrome plated Phillips Head Screws. The upper four holding the stand to the motor housing (I used a manual impact driver to loosen the very stubborn, #4 Phillips screws) must be removed so as to access the four smaller Phillips machine screws (no lock-washers found here, best buy at least four #10, split, before reassembly) 2. Lastly, you will need two pin punches however the recommended smaller 3/32 inch is still too large to remove the pin in the tower assembly. You will need one size smaller or a #4 pin punch instead. These older Kitchen Aid mixers were built with very tight tolerances. Please be patient and take your time removing the pins. Good Luck……. Jim

I did some research and evaluated a modern day Kitchen Aid Mixer. Looked a the wire diagram and found out what items I needed. Ordered them from Partselect. Overall Mixer is updated and running. I made up some cookie dough with it. The Project took a few evenings due to rewiring the coils on the motor/armature and modifying the rear bearing bracket to hold the Phase control board (not OEM on 70's mixers). Then put it back together and adjusted the speed control.

watched an internet video to see what to do. Unfortunately even after replacing the chip the mixer it still didn't work.

Fairly easy if you have done it once before.

disassembled replaced part reassembled now works well

I followed the instructional video linked to my email order confirmation. Partselect provided one of the best how-to videos I've ever seen. With the right tools, a little patience and the video, I had an outstanding repair experience.

i disassembled the mixer until i could remove the worm gear; is in a housing that that includes another gear and shaft. make sure you have a magnetic tray to put parts in as you work or you will spend more time looking for parts than reassembling the mixer. once you have the gear housing out you will need a small diameter punch to drive out the pin that holds the gears in the housing(i used a 5/32 transfer punch.) make sure you punch the pin out where it will be caught or you will need to order that part because you will not find it. after knocking the pin out it is just a matter of removing the old gear, putting the new one in, and reversing the steps and getting everything reassembled.

Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.

Follow a YouTube video step by step

Order the worm gear part number PS11748374.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk

I would recommend two people if possible.