Models > KSB5OB4 > Instructions

KSB5OB4 KitchenAid Blender - Instructions

All Instructions for the KSB5OB4
76 - 90 of 499
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No proplem
Went easy
Parts Used:
Blender Blender Coupling
  • Jon from WILLOWICK, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blades On Blender Locked Up
Piece of cake. Part was expensive and shipping likewise. Very fast
Parts Used:
Blender Blade Assembly
  • PAUL from LAWRENCE, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coupling had broken a couple of pieces off
Intructions were simple. Pried off the old coupling with the screwdriver and applied presser to replace the new one on the spindle.

Comment: KitchenAid appliances are made to last unlike most other small kitchen appliances. They are made of strong materials and repairable where as other similar products get thrown out when they break.
Parts Used:
Blender Blender Coupling
  • Ernestine from Madison, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Teeth on rubber coupling were broken off.
Just like the directions said, I pryed up on the coupling at a few points around it's circumference and it became loose enough to unscrew. I didn't believe it was going to work at first but, amazingly, it did. All that was left to do was screw on the new part. No problem!
Parts Used:
Blender Blender Coupling
  • Tom from Phoeniox, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coupling's two extrusions broken
with a flat wrench grab the shaft and unscrew the coupling (note: left handed threads)... then install the replacement part.
Parts Used:
Blender Blender Coupling
  • Mario from Virginia Beach, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coupler wore out
i used the screwdriver method prying up on side to side old one comes off new one goes on pretty cool also it was a nice long flat head with pretty big head
Parts Used:
Blender Blender Coupling
  • Chris from hawthorne, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Coupler broken
It was very easy to unscrew the coupler I used locktight to put on the new part. Thank you sending
the right part the first time
Albert
Parts Used:
Blender Blender Coupling
  • Albert from Frenchtown, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cup drive on blender was stripped.
Released cup drive with screw driver and un-screwed, screwed on new driver.
That is all, works like a new blender.
Parts Used:
Blender Blender Coupling
  • Frank from Athens, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The drive coupling wore out
I unscrewed the old coupling and screwed on the new coupling from Partselect.
This was a personal repair job.
However, I am a local Handyman in Northern NJ that does a ton of minor repairs. For all of my appliance part needs I will buy from Partselect.com. They under promised and over delivered! Just incase you dont know what I mean by that statement,,, I ordered the blender part, they told me I would have it in 6-10 days (which was acceptable to me) and I had it in two days... AWESOME job FOLKS!!!!!!!
Parts Used:
Blender Blender Coupling
  • Brian from Glen Ridge, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The coupling teeth on the blender broke off when it wasn't seated properly
After reading repair stories on this site, I used wire splicers that just fit between the coupling and housing to hold the shaft while I used pliers to remove the broken coupling. I then hand tightened the new one . It works fine now.
Parts Used:
Blender Blender Coupling
  • Jerome from Salem, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
coupler crumbled
Thanks to everyone before me and their stories!
I felt confident enough to try repairing my blender myself ! ! !
I just placed a flat head screw driver under the coupler and pushed up on the screw driver, 3 or 4 more times around the coupler. It broke away and a metal disc was left, which I unscrewed and I just screwed the new coupler on.
Thanks Again!
Parts Used:
Blender Blender Coupling
  • Carol N from Northford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Teeth on the drive coupler worn completely off
Followed the directions and used a screwdriver to pry off the old gear. Screwed the new one on - reverse thread. Easy as that.
Parts Used:
Blender Blender Coupling
  • Brent from Austin, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken base coupling on blender
used thin wire strippers to hold screw shat, than unscrewed one and screwed on the other. done
Parts Used:
Blender Blender Coupling
  • jeffrey from Bessemer City, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The rubber coupling that spins the blender dessinagrated
Popped off the old one and popped on the new one. It took no more then 30 seconds and the blender is like new again.
Parts Used:
Blender Blender Coupling
  • Lisa from Poway, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rubber drive coupling on blender broke apart
Followed the instructions that came with the replacement drive coupler, first removeing the old part using a screw driver, and then easily screwed on the new part. Removing the old part without the aid of the instructions would have been problematic.
Parts Used:
Blender Blender Coupling
  • Jack from Corona, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KSB5OB4
76 - 90 of 499