KRSC500ESS01 Whirlpool Refrigerator - Instructions

Took lower back board off, took part off to expose it so I could see where it was leaking, got part number, ordered it.
Shut off water to frig at wall shut off, unhooked both hoses and plug, hooked new part up, turned water back on. Watched couple days to make sure it wasn't leaking. Vacuumed out back good, which I was amazed didn't really need it, hooked part back in place, replaced back with screws.

Simply cut the water tube on both sides of connector and push in the new one.

I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.

Remove the top two drawers, with a small screwdriver pop out module, unplug, plug in new module, press back into place, put drawers back, DONE! 5 minutes easy peasy ??

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

There are 3 tabs on each side of light that fit into hole in freezer. Pushed putty knife under edge of light. Inserted 2nd putty knife midway down. Push both putty knives in toward light and gently pry up 1st knife until plastic clip is released. Remove 1st knife and insert near bottom and push in. Pry up mid level knife and unit should pop ou. To install just puch new LED light into hole.

Open door and from appliance instruction book
Replace filter

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Got resistance values from partselect. Coil was not in range. I remove rear cardboard cover,shut off water. Valve located on right side rear. Hoses are quick release. Unplug wire harnesses.

At first ordered the wrong part. Using the website was difficult to find the correct part, but once I called, it was pretty easy to find the part needed. Part showed up and install was only a few minutes. No more leaking!

Thanks for the help PartSelect!

added an additional shelf to the refrigerator section of our Kitchen Aid side by side refrig./freezer

Received a brand new right side door from Parts Select.com. Unpacked the door and checked its condition after shipping and found to be perfect. Removed shelf storage units from the old door on the refrigerator. Removed handle and handle mounts on front of door with allen wrench. Used two different size star bits (#30 and #25) on the upper door hinge screws (4) on top of the refrigerator. Unscrewed hinge and lifted door off the lower hinge.
Placed the new door on the lower hinge and reattached the upper hinge with the screws. Re-installed the shelf storage units on the inside of the new door. Reinstalled handle mounts and handle on door.
Note: the new door required very little adjustment in alignment to the left door.

I ussed meter to check the voltage levels and they were fine. I refrence a you video on the refrigerator and foud out that the lights are setup in series like christmas tree lights. If the freezer light is out it will affect the rest of the lights in the refrigerator. I removed the freezer light module and test the light by swapping it with a know working light. the freezer light was the culprit that took the lights out in the side panels and the left side of the refrigerator section. I replaced the freezer light and all the lights now work without issue.

One light and they all go out. So i used one fo lights