KPDI620T5 KitchenAid Dishwasher - Instructions

Was lucky the part was available. I put liquid detergent on both ends of tube, then slid each end onto each sleeve. Works great now!

I removed the old tube. I rubbed vegetable oil on the inside of both ends. The new tube slipped on with no
problem, and that was the end of the repair.

pulled off the old and put on the new. Great pictures on website so I got the right part the first time. Thanks!

It was 94 degrees that day so I set the rubber hose outside in the sun to loosen it up, make it more plyable. I then mixed up some soapy water and doused the ends of the hose with the soapy water and slid the hose right onto the fittings.

There was a small hole in the hose which was not discussed in the directions. I assumed the hole should be installed on the down side to let water drain out after the dishwasher is finished. This will reduce the chance of bacteria building in the hose.

I read the installation tips before I started and picked up the soap mix and heating up the hose before installation. Can be accomplished with a hair dryer if it is not 94+ degrees outside!!!

Thanks,

Jim

connected tube to spray arm and attached to back of dish wash machine.

I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.

One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!

the tube slid off and I used some liquid soap to spread on the end of each tube and I slid the new tube back on with ease and the upper rack of dishes now get cleaned/rinsed.

Pulled off old tube, applied small amount of lubricant to each end of tube, then just pushed ends together. Slide right on, attached new support and in less then five minutes, fixed. Dishwasher running like new.

removed old hose slid the new one on. Easy one minute job.

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.

One of the axles broke off, requiring no removal. The other wheel broke off, but the axle remained. That required squeezing (pliers) to push out. Replacement was easy; just put wheel onto axle and push axle through mounting space. Total: 5 minute job.

Our old Kitchenaid Dishwasher was not getting the glasses on the top shelf clean. I looked and found the tube running to the washer arm under the top basket was split.
I replaced the tube. First I put dish soap in the ends of the new tube, so they slipped onto the other parts with only moderate force.
Now the dishwasher is making the glasses in the top basket clean again.
Regards,
Bob

The hardest thing was getting the old one off and easy snapped the new one on

I removed the roll out top wire rack of the dishwasher, turned it over and pulled the old punctured water supply tube off the force fit connectors on each end. I put a small amount of vaseline lubricant immediately inside the mouth of the new tube at each end. I pressed the ends of the new tube over the force fit connectors and tested them by shaking the pipe. I replaced the rack and fastened it into place.