All Installation Instructions for Whirlpool Mixer KL26M2XOB5

attachment planetary gears stripped

removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.

Parts Used:

Hub Gear

Gearcase Housing with Gasket

John from ST AUGUSTINE, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Planetary Pinion Gear Assembly had dropped down

The repair was easy, I only had to order new gear assembly parts and to replace the associated worn parts (shaft, pin, and gears).

Parts Used:

Hub Gear

Worm Following Gear

Mixer Retaining Pin

Mixer Lower Bearing

Karl from Hammond Ranch, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Gear Stripped was trying to replace

Could not get it properly installed. Had to take to a repair center for completion.

Parts Used:

Worm Following Gear

Stuart from Pittsford, NY
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

I stripped a couple of gears due with a batch of very hard dough

Taking apart the machine is really easy. I was worried the grease would have spilled all over the places, but when the machine is cool, the grease is solid, so no spill. Replace the parts is quite straightforward, and there are plenty of tutorials on line. The only tip is that the grease used by KitchenAid is dark, and it is not easy to see all the small parts when you take the gearbox apart, so pay attention at what you do and at what you throw away... when I got to put it back together I missed a special concave washer which must have been trapped in the grease. Other than that... it has been an easy repair, the mixer is back up and running and I saved a ton on $$$

Parts Used:

Mixer Transmission Gasket

Mixer Thrust Bearing Kit

cosimo from EL CERRITO, CA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Stripped Gear Mixer would not mix

I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.

Parts Used:

Worm Following Gear

Robert from PEORIA, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

REPLACE SPEED CONTROL SWITCH

REPLACE SPPED CONTROL SWITCH

Parts Used:

Stand Mixer Speed Control Board and Knob (Black)

FRANCISCO from SAN BENITO, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken gear case.

Remove and replace gear case. Apply food grade grease secure with screws.

Parts Used:

Gearcase Housing with Gasket

David from CEDAR CREEK, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

dryer was making a screeching noise

replaced the two Bearing slides thanks to your video repair was quite easy

Parts Used:

Flat Metal Beater

Edgar from LITCHFIELD, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Speed switch bad and Initially thought new part was wrong!

At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.

Parts Used:

Stand Mixer Speed Control Board and Knob (Black)

Richard from Harrodsburg, KY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

The mixer started making a loud knocking noise

Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .

Parts Used:

Hub Gear

Reza from STAMFORD, CT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

white plastic part on the lifter handle

Took off all the screws to open the mixer and install the new parts.

Parts Used:

Bowl Arm Lift

ROBERT from LARGO, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Worm gear stripped.

Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.

Parts Used: