Models > KHWS02RMT3 > Instructions

KHWS02RMT3 KitchenAid Washer - Instructions

All Instructions for the KHWS02RMT3
91 - 105 of 206
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Tub filling when power was off due to inlet valve leak.
Followed instructions as shown on repair video at site.
Parts Used:
Washer Water Inlet Valve
  • Francisco from DELTONA, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
tub would not turn
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Parts Used:
Washer Drive Belt
  • claude van from big sandy, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of my baffles just came off during a wash, one of the plastic clps that hold it in place dry rottedafter 10 years
Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
Parts Used:
Washer Baffle
  • scott from DENVER, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The video supplied by you was great and it worked very well.
It was fast and pretty easy to do.
Parts Used:
Washer Door Bellow
  • Michael from NEWBERG, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Parts Used:
Inlet Hose - 5 FT
  • Helen from NASHUA, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was done.
Parts Used:
Washer Drain Hose
  • anthony from EASTPOINTE, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inlet valve was stuck in open position allowing washer to fill with water when not in use.
Removed lid. Took old parts off and replaced with new parts. Also replaced hoses while washer was moved away from wall.
Parts Used:
Washer Water Inlet Flowmeter Washer Water Inlet Valve
  • john from YARDLEY, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer leaking
Followed internet instructions
Parts Used:
Washer Pump Hose
  • Carolyn L. from CLAYTON, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drum baffle broke and had to be replaced
place new baffle over slots in drum; move toward back of drum and snap in to place pressing down and moving toward front of drum
Parts Used:
Washer Baffle
  • Alan from GOUVERNEUR, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washing machine was not draining. It was showing a code on the washer of 02.
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Parts Used:
Drain Pump Kit
  • Robin from Gary, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the pump wasnt puping out the water
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Parts Used:
Drain Pump Kit
  • Evette from Mayfield, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
Parts Used:
Washer Door Lock Latch
  • Keith from Amherst, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't drain
Easily. 4 Screws. 2 Clamps.
Parts Used:
Drain Pump Kit
  • Jeff from Barrington, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace tub to pimp hose.
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Parts Used:
Washer Pump Hose
  • Bob from LORAIN, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bellow leaking water
Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.
Parts Used:
Washer Door Bellow
  • Eric from Vacaville, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KHWS02RMT3
91 - 105 of 206