KFIS27CXMS4 KitchenAid Refrigerator - Instructions

Repair was replacing motor kit. I did not use the plastic parts - ejector arm and separator. Went same as others described. I had removed ice maker from refrigerator although this was not necessary to replace motor unit(Please unplug refrigerator whether or not you remove the entire ice maker).
Removed three screws, removed old motor unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.

Repair worked. Have lots of ice again.

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

Turn off the water to the unit. Disconnect the plug on wiring from the old valve.
They always recommend you disconnect the electric (unplug) the unit while doing this work.
Disconnect the water lines from the old valve by pushing the water line slightly into the flange on the valve, it releases the line from the flange.
Hold the flange rim against the valve seat and pull, you may have to jiggle the water line a little while pulling to remove it.
Push the water lines into the ports on the new valve, turn on the water and check for leaks.
If no leaks, plug the wire connections onto the new valve, reconnect it to the unit and turn the power back on.

Changed the ice and Water filter, works great...

Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!

Popped out the old switch and replaced it with the one dying

Bought new cap.

Simply removed the phillips head screw and put the bushing and washer and coupling back in place and replaced the screw. Hardest part was breaking the screw loose to begin with. After that it was a snap. Less than 15 mintues and i was crushing ice again. Ordered two of the couplings so I have a spare when this one snaps. I think this is a re-curring problem for this model.

Just plugged it in

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!

I watched a YouTube video real quick to see what I had to do and got to the job at hand. I removed the old gasket by pulling it out of the track and bring it around the front of the drawer. I wiped down the entire area where the new one would go and started inserting it into the groove, making sure it went in completely in on the bottom. I was done in less than 15 minutes. Super easy! This fixed the issue and the freezer door closes fully.

Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.

Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.

Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.

Followed directions on filter unit

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?