KFIS20XVMS8 KitchenAid Refrigerator - Instructions

Removed two screws on outer face plate and set aside the face plate after disconnecting from power supply. Remove dispenser paddle which had broken and replaced with new part. Reattached power connections and reattached the face plate. Relatively easy process.

Replaced two original crisper drawers with 2 new drawers; replaced broken end cap which required the removal of a few bolts and screws. The replacement parts were identical matches--a huge relief. The interior of the fridge looks like new. This follows upon not being able to get the parts directly from the manufacturer.

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.

I unpacked the glass and slipped it into the shelf. Done.
What was more impressive was the delivery time. I ordered the glass at about 12:30pm one day and the glass was at my door by 9am the next morning. Even my husband was impressed with that.

I had to replace the entire door because the plastic tabs holding the window in place snapped off. I just opened the door to see how it was held in place, released the old door and installed the new one. Job complete in less than a minute.

Repair was simple and just as described by several others on this site! From finding the part, ordering, quick shipping and instructions, PartsSelect made this job a breeze to complete.

I removed the Deli Drawersvegatable and fruit drawers. Removed the glass panel. Removed the screws holding the Endcap and snapped the old one out. A back panel strip that controls the humidity snapped out. I installed the back panel to the new endcap. Installed the new endcap snapping it in place and used the screws to keep it in place.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.

after pulling the draw out. had to remove 3 screws on the left side, pull out one part, and then replaced the broken pin. put everything back in place and it was done.perfect job.saved alot of money. thanks to part-select

I fumbled a large jar of olives that hit the deli tray, inside lining and top of bottom freezer drawer before making it to the floor. The deli tray cracked, a gash was in the white bottom lining and the SS top of freezer drawer was dented. Service and delivery was excellent, fast and installation was a matter of popping the tray cover off and snapping in the new one. Now, if I could only change out the liner myself.........

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".

To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.

The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.

Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.

The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.

Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.

Once the motor module is seated, replace the 3 screws and push the white cover back on.

Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.

Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.

The icemaker should start making ice within 2 hours.