KFIS20XVBL2 KitchenAid Refrigerator - Instructions

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

Repair was simple and just as described by several others on this site! From finding the part, ordering, quick shipping and instructions, PartsSelect made this job a breeze to complete.

Removed two screws on outer face plate and set aside the face plate after disconnecting from power supply. Remove dispenser paddle which had broken and replaced with new part. Reattached power connections and reattached the face plate. Relatively easy process.

Removed the whole ice maker unplug one wire harness replaced ice tray with new one.
Very simple.

Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.

stick the very small screw driver in the hole on the left side cover and lift up to release the keeper tab,pull out to expose the wire connecter.insert the small screw driver in the slot on the left side to release the tab while pulling apart the two connectors.tuck the wires tight to side and pull out the ice maker.I thought I was getting the whole ice maker assembly,but just got a part of it,so I had take it apart and put it back together.the hardest thing to change over was the stop lever arm that senses the level of ice in the bin.after all this,it didn't work at all.not happy around here.back to filling ice trays

I was hesitant to remove old seal, after I removed, I lined up new seal, and the seal popped into the slots very easily. Easy repair, no tools, worked great. The seal takes about 24 hour to seat itself for a great fit.

No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help

Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm from old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.

Removed two 1/4" screws from the end cap with the nut driver and removed it. Transferred a few pieces from the old end cap to the new. Reinstalled the new end cap and presto, job complete.

I removed the Deli Drawersvegatable and fruit drawers. Removed the glass panel. Removed the screws holding the Endcap and snapped the old one out. A back panel strip that controls the humidity snapped out. I installed the back panel to the new endcap. Installed the new endcap snapping it in place and used the screws to keep it in place.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.