KFCK03ITWH0 KitchenAid Trash Compactor - Instructions

There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

Installed new parts. Worked fine.

Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.

Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

Removed bottom and replaced gears

After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!

Inserted three screws in pre-drilled holes.

Removed two screws, replaced handle, replaced the two screws. This was so simple! I can't believe we put up with the inconvenience for so long before fixing it!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

the bearing were the perfect match and instructions helpful. sysem is rolling smoothly

Very simple, changed the gear, adjusted the drive and tested. Very straight forward.

Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.

Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.

At best it is advisable to load just one at a time and covered with newspaper etc., In this case someone put in three bottles with out covering with heavy newspaper etc.and for some reason one rode out and to the side. Crushing the side of the metal trash container. This pinned the container against the side of the compactor body and behind the front rails. Using a lot of pulling and some nifty pry bars and two hours of prying and squeezing we got the container out( see attached photo )The replacement container was ordered on a Sunday night and arrived Tuesday morning. Removal of the existing front panel ,foot pedal and door switch was easy and installation on to the replacement container was a breeze with a little orientation required to line up the switch and pedal in the right configuration. 20 min tops and that was with five kids helping ;)

bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.