KF26M2XNP5 KitchenAid Mixer - Instructions

The rear 'loop' on the bowl assembly broke off when our cleaning lady tried to wrench the bowl lift handle in the wrong direction. The loop connects to the handle with a rod and spring and the bowl lift mechanism is the piece that slides up and down. I tried to weld the loop back to the bowl lift, but because it is aluminum, it didn't work very well. I purchased the new bowl lift assembly with a new spring (thought I'd lost the first one). This came just as if from the factory, slid it on the track, inserted the rod and screw into the loop and tightened the fastening nut. Easy peasy. Saved myself a $300 - $400 new kitchen aid professional mixer. It did take about 1.5 - 2 weeks to arrive, but it did and that's what counts. Very pleased with my experience.

took off the strap band around mixer, took off the cover (4 screws, took off gear cover (4 screws) took off the retaining ring(used pliers and screwdriver) took off upper gear, took out retaining pin, took off lower gear (becareful to grab the planetary assembly as it will fall out after you take out the retaining pin) cleaned out all of the gear grease (the teeth that were missing were in it. replaced the planetary assembly, lower gear and retaining pin. replaced the upper gear, replaced the retaining ring (used screwdriver and hammer. you have to spread the ring with end of screw driver so it will fit on the shaft then tap lightly with screwdriver and hammer to get it down to the keyway for the ring.) replaced the gear grease with NEW grease, reaplaced the gear cover, replaced the mixer cover, replaced the strap band and plugged it in to test it. IT was quieter than before and works great. i spent less than $30 to repair my 10 year old, out of warranty, Kitchen Aid Mixer. much better than the $32.00 to ship it to factory repair shop and get an estimate to repair. I needed it to make a cake for my nephews wedding. I had my parts in 2 DAYS!!! it was a great experience over all.

We are a pretty handy bunch here. However, the diagrams provided with the part numbers did assist in the disassembly. It went smooth and easy.

Open the case, removed gear cover, removed planetary drive shaft and gear, replaced with new planetary and reassemble.

___ Remove silver decorative band/1 screw ___ Remove top of mixer/4 screws ___ Remove circuit board/2 screws ___ remove 5 wires from ckt. bd. (be sure where they go) ___ Install new ckt. bd. with proper electircal connections ___ test mixer/OK ___ Reassemble & retest/OK

Following Replacement Part Youtube instructions, I disassembled the mixer and found what caused the sounds and prevented the mixer from operating. The worm follower gear had been ground down by the worm gear. I found that the shaft from the planetary gear had not been adequately greased and siezed preventing the worm follower gear from turning. The worm gear is obviously made of harder material and thus, was able to wear away the follower. I appreciate the your help which saved having to replace a perfectly good/expensive mixer. Thanks.

Remove screw and nut from back of mixer head to release the silver name band. Remove the exposed four cross head screws, (two each side), and lift off the motor and gear cover. Wipe excess grease from gear wheels to expose the retaining ring clip at top of vertical gear shaft. Using small nose circlip pliers, remove retaining ring and bevel gear wheel to expose shaft pin and worm gear. Support the shaft from below and remove pin. Lift off worn worm gear wheel allowing shaft to drop down. The horizontal worm gear shaft can now be lifted out taking care to keep assembled. Carefully clean old grease from all gears and from the gear housing, (note that broken pieces of the old worm gear are in the old grease. Repack housing with fresh high performance grease recommended for worm drives. Cover new and reuseable gears with grease. Reverse the process to reassemble the unit.

Took housing off, removed computer board and disconnected speed control assembly from board. Soaked plastic slide in hot water and freed up mech. Discovered a crack in plastic slide from forcing it. Ordered new assembly and installed. TIP: Keep slide clean of substances that will jam it by cleaning occasionally with water. For a complete cleaning you will have to remove it. Total of 6 easy to reach screws.

Easy repair that replaced the variable speed switch. The broken switch only ran at high speed. To replace the mixer would cost at least $500. The new switch was $45 and was an easy install. I marked the four electrical leads with a Sharpie and loosened the two screws holding the switch. The repair was super easy. It was like heling an old friend recover from an illness.

I have to thank you at Partselect.com. You happen to help me help other people. Now I have several people bringing me their Kitchenaids to me instead of sending them in. I replaced two worm gears on a Kitchenaid 6 and the Hall sensor on a Kitchenaid 5. Very easy to do. Next week I have another Kitchenaid 5 to replace the motor on. Thankyou again for having the parts I need

Looked at the schematic for this model on Parts Select. Removed Aluminum band screw, removed the 4 screws that hold the top of the mixer. Lifted the top off. Removed 4 screws and lifted the gear case. Removed snap ring and took off tapered gear. Removed pin and removed worm gear. Picked out the metal, in the grease, from the old worm gear, using a magnet then inserted new worm gear and put it back together in reverse order. There was plenty of grease and didn't need to add any.

Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again

ordered the part and put in in with the help from the instant repairman

replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.

Open the package with the new screw and it looked like the screw was wider. I tried it to see if it goes in and as long as you screw it straight in, there was no problem.