All Installation Instructions for KitchenAid Range KESV908PMT01

After using the self cleaning feature for the 10th or so time, the range locked up and nothing worked.

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

Parts Used:

Range High-Limit Thermostat

Shay from KITTY HAWK, NC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

wire came loose and shorted out

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Parts Used:

Range Main Power Terminal Block

Elizabeth from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Glass broke in the oven after I wiped is with a damp cloth after a cleaning cycle.

It went fine once you imbeciles sent the right part, thank you for miss labeling it on the website and costing me time, a week without an oven, and extra expenses. The inner GLASS is the inner GLASS, not the middle glass of a layered three glass door!

Parts Used:

Range Inner Door Glass

JOAN from PARKERSBURG, WV
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Not heating up properly

Installed a new thermostat and noticed the convection heating element wire had burned in two. Ordered new element and installed. Oven is currently working properly again.

Parts Used:

Element

Harmon from MONTICELLO, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

broken inner door glass

It most likely would have gone quickly had we ordered the right part!

Parts Used:

Range Inner Door Glass

Ann from GRACE, ID
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Block broke

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Parts Used:

Range Main Power Terminal Block

Edward from Crimora, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

broken meat probe

My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.

Parts Used:

Range Temperature Probe

Daniel from Massey, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The oven shipped without a temperature probe.

Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.

Parts Used:

Range Temperature Probe

jerry from rochester, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

23 of 74 people found this instruction helpful.

Was this instruction helpful to you?

range installer broke a screw off & busted the plastic piece

Had to screw off old terminal block & screw on new one

Parts Used:

Range Main Power Terminal Block

Christina from West Des Moines, IA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

terminal block cracked

Followed the easy instruction sheet provided.

Parts Used:

Terminal Block

Range Hex Nut

James from Richmond, VA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

terminal block back of range shorted and burned

EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare

Parts Used:

Terminal Block

Louis from Grantsville, UT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

When removing the warming drawer I did not read the instructions and broke the slide for the drawer. I removed the drawer without pressing the tabs which broke the right slide.

I removed the broken slide by removing 1 screw on the front slide and the back of the slide came out of the slot in the very back (no screws). I fitted the back of the slide into the slot and then replaced the screw on the front of slide. Extended the slides then I pressed the tabs on the drawer and replaced in onto the slides (left and right) . Closed drawer and finished! Very easy!

Parts Used: