All Installation Instructions for KitchenAid Range KESK901SSS02

worn out hinges

Tried reusing old door hinges after removing door to access temp sensor and broke the oven glass twice.with new hinges , new glass went in easily.

Parts Used:

Door Hinge

Kenneth from West Orange, NJ
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set

Was this instruction helpful to you?

terminal block cracked

Followed the easy instruction sheet provided.

Parts Used:

Terminal Block

Range Hex Nut

James from Richmond, VA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

element went bad would not heat

Removed screws that hold element remove wires from old element replace with new one replace screws turn power back on at breaker box done.PS make a steak done.

Parts Used:

Element, Broil

Bruce A. from Adena, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

One of the burner wasn't light up.

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

Parts Used:

Radiant Surface Burner Element 1500W

Sam from Fairport, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

not needed

screwed in the new oven light

Parts Used:

Range Light Bulb (15w)

Peggie from Gresham, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Wiring Block shorted due to moisture and Stove had no Power

This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.

Parts Used:

Terminal Block

John from Roberts, MT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Broil element was shorted out and not working.

Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.

Parts Used:

Element, Broil

NANCY from CARLTON, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

terminal block back of range shorted and burned

EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare

Parts Used:

Terminal Block

Louis from Grantsville, UT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Not Heating

Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.

Parts Used:

Range High-Limit Thermostat

Gayle from Shelby, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

burned out oven bulb

unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.

Parts Used:

Range Light Bulb (15w)

benjamin from conway, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

burner bad

looked it up on line how to change it. before I ordered part, to see how much of a job it was. was real simple to change, had no problem. also part select sent the correct part. Job went well

Parts Used:

Surface Element

Edward J from Baxter, MN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

While trying to tighten the oven door handle, the outside glass shattered.

I was not able to order just the glass, so I ordered the exterior door assembly. The door assembly is held in place by 5screws. 2 on top, 3 along the bottom. A very easy project!

Parts Used: