KERC600GBS1 KitchenAid Range - Instructions

Had to remove drawer under range to get id number with flashlight. Ordered the part from a very helpful employee and it arrived in timely fashion . I placed the knob on the rod on the stove top and Voila! Excellent service. Thanks.

real easy one to take care of, when the drawer broke I thought it was more than what it really was, after looking at it and seeing the wheel was gone I ordered the part and it came very quick, drawer is now fixed.

Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.

All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!

Never repaired an oven before, I just used a screwdriver and went slowly taking this over door apart to replace this glass. I just took piece by piece apart until the glass came out and retraced my steps to install the new glass. Sure glad I did this myself, a new convection oven stove would easily set me back 1,500.00 and......save a bundle on service call fees.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Removed the door just like you would do when cleaning the oven; I placed the door on a blanket on the kitchen table and carefully disassembled the door. There were more parts than I expected so keeping track of where everything went was important. I might add that without the use of my cordless variable speed drill motor removal of some of the screws would have been difficult. Adding the weight of the drill motor with sufficient push power I was able to tap the switch which "snapped" the screw loose. Don't think I could have done it with a hand type screw driver without stripping the head. Knowing your tools is very important.

Purchased 2 piece broiler pan from this site

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

removed back of stove, removed 2 screws holding element, disconnected element and removed it, then reversed procedure. excellent service from part select and will use them again when needed.

In my situation, removing the control panel first required pulling the range unit forward to expose the side screws, which first required removing the screws holding down the stove (tilt prevention. Those screws are accessed by removing the bottom range drawer). Replacing the switch was a breeze. Very important to label wires before removing them from the old switch. Also, over the years, food liquids that spilled on the range top "gunked up" the front gasket seal of the control panel. Suggest cleaning the gasket as part of the repair - something a DIY should always do! Leave it better than you found it. When I removed the current switch, I could tell by looking at the LED terminal post there were burn marks which suggested there was indeed a fault in it. For about $45 I replaced a switch that would have cost over $200 for a repair person to come.

Read all others' directions and suggestions. Screw loosening spray was essential to remove the bracket holding the broken piece. Print out the blow-up showing parts from website. Read directions on removing and replacing door in original manual. Lay oven door on counter top front side up with hinges hanging over edge. I prefer a manual screwdriver - less risk of stripping screws. Start by removing screws at bottom edge. Next, side strips and then top piece with handle. Removing layers, being careful to keep them in order and turned the right way. Note the center piece of glass is held in place only by the parts around it so everything has to be tight and aligned. Put back together in reverse order with replacement glass part. My 10+ year old oven is as good as new. BTW I am a 67 year old woman.