KDTM354DSS4 KitchenAid Dishwasher - Instructions

I basically used the instructions provided with the "Your Order Has Shipped: email from you. It was quite easy. Thank You!.

The rubber door seal was easy after watching the video. I key point however is that you do have to stretch the seal just a little bit. The video says not to. If you don't like I didn't originally, the seal will only extend from one side to the other without about an inch excess that folds on the bottom of each side. The door still leaked a little without the excess folded on each side. I did one side at a time and pulled out the new seal along the side before curving to the top, and just stretch it slightly to allow the excess. This stopped the leak.

The lower door seal was ok to do. The most important step there is to remember how the front door panel is installed. Taking pictures before and during removal may help. It is awkward to do by yourself, but can be done. I found that putting a balled-up towel at the top of the door helps when trying to reinstall the front panel.

Two of the four small nylon/plastic tabs on the adjusters that support the top rack on the rack slides, broke off (one on each side).

Before the new parts arrived, I printed the limited (but definitely helpful) instructions that were available and familiarized myself with the adjuster assemblies.

As practice, I took one adjuster assembly apart making notes of any "gotchas." The main gotcha I found is that the nylon/plastic parts are easy to break (obviously) as prying is involved during removal and replacement. It took me about 20 to 25 minutes to take one side apart and about 10 minutes to put it back together again.

When the new parts arrived, I was able to do the first side in about 10 minutes (removal and replacement), and the second side in about 5 minutes, all because I had printed the instructions, familiarized myself, and practiced. I hope this helps.

Thought this would be much easier than it actually was. Long story short, ended up calling is an appliance professional to install the part.

Still not sure it is repaired. Still have water leakage around upper edge of door on control data panel. We just experienced an issue with the auto drain system, the first since door seal repair and door latch replacement???? Is the latching mechanism suppose to secure the door?
If so it isn't?
Not a great success story. A new washer may be in the cards

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Popped damaged/worn wheel assembly off, snapped new ones in. Easy peasy

Removed the inner panel, remove electrical connection to dispenser, remove dispenser, metal tabs that hold it in, are a bit hard to pry metal tabs, and when installing net dispenser tabs are also a little difficult to pry tabs to install but doable. So far works like it should.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

I did a Youtube search and discovered there were a couple that showed the replacement in detail. I watch the entire process once and then had my laptop beside the upper rack and paused the video after each step. That worked well

Removed old housing parts and replaced them with the new parts I ordered. Very easy

pushed the new retainers in the holes and we are set to go

Float switch right in front. Did not remove dishwasher. Used small flat screwdriver to un clip cover. Very soft and easy. Unplug and it slides out.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.

We watched videos on this repair but they didn't matter. All we did was remove the lower rack of the dishwasher. To remove the broken assembly we put pressure behind the wheels pulling them out and up - it popped right off. To install the new wheel assembly, it was easy to see where to align the part and my husband snapped it back in. No tools. Easy peasy.