KD835ADK2 Frigidaire Range - Instructions

took off the back of the stove..first Unplugged it! and undid the old unit, and put the new one on....easy peasy!..Thanks for your fast mailing!

Removed sheet metal plate from back of oven. Disconnected two lead from existing bake element. Removed existing bake element, replaced with new one. Connected wires, replaced sheet metal.

The trick with this old oven is to access the wires from the back.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.

***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.

I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.

I just followed the instructions that I found online.

They don't make appliances this easy to repair anymore. just as others say: screw out, unhook element ..hook new one to wires, screws back in.. you're DONE.. Thanks for great service and very quick delivery

unscrewed rear connections, removed broken element, installed new

I figured that it could not be a hard repair, that these things "die" in the ordinary lifetime of an oven, so that they would not make it too hard to get to. I pulled out the oven and disconnected it; opened three screws on the back, took off the back plate, and you could easily see the two connectors to the element. They came off with a gentle tug with pliers. Then you open the oven, and remove one screw on each side where the element is connected to the back wall of the oven. A magnetic hex socket end for the screwdriver makes it easier. Remove the old element gently through the glass wool insullation, and insert the new one with the element "legs" down. Verify the placement of the element connections in the back, and then replace the screw that hold the tab on the base of each element side to the back wall of the oven. Then, carefully reconnect the connector sleeve onto each end of the element in the back of the oven snuggly. Close the back panel with the three (the forth on the top was not tight and didn't need openening or closing)screws to the sides and bottom of the panel. Replace oven and reconnect to power, and test the element. It all took less than half an hour.

Locating part on web site, ordering, receiving next day & installing was very very easy. Information provided on PART SELECT web site and that provided with part made this a very easy and cost effective repair. With service provided by PART SELECT there is no reason to pay for an expensive service call in addition to what a repair company would charge for the part.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.