KD220GDW2 Frigidaire Range - Instructions

jim from gorman, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

My burners were shot!

Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!

Parts Used:

Surface Element - 6 Inch

Karen from POPLARVILLE, MS
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Burner on stove stopped worker

I did as instructed on your video of how to install the terminal block, btw GREAT VIDEO!!
I'm a 66 year old female and if I can do it, anyone can.

Thanks, PartSelect

Parts Used:

Surface Element - 6 Inch

Virginia from MT PROSPECT, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Old drip pans had turned to rusty lace.

Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.

Parts Used:

Helen from PAWLEYS ISL, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Left an appliance on surface element and melted paint onto the element

Plug the new element into the space on stove

Parts Used:

Surface Element - 6 Inch

Kenneth from LANOKA HARBOR, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Drip bowls needed replacing

Removed the old ones and inserted the new ones.

Parts Used:

Doris from SUN CITY, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

needed new drip bowls and 2 new elements

pulled them out and replaced them

Parts Used:

kathy from DAVIS, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Burner would cutoff intermittently

Pulled out old burner/inserted new

Parts Used:

Joseph from FREDERICKSBRG, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Rusted Drip Bowls

This range is probably 30+ years old. Still works great. Just needed to replace the Drip Bowls.

Parts Used:

Carolyn from OCEAN PARK, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Terminal block was bad.

Cut the old block off tied new wires to hot wires . That easy!

Parts Used:

Terminal Block Kit

Chuck from EVANSVILLE, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Bake element not working

Removed the old element by sliding the wires
attached to it. Unscrew 2 screws, slide the
new one to the wirings and put the 2 screws back.
It works. Praise the Lord.

Parts Used:

ROMEO from HANOVER PARK, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

bottom element broke and would not heat

the repair itself went smoothly. the clips that the new part connected to were old and slack. the clip came undone and had to pull the stove out to get to part from the back. i squeezed the clip together to make it stay on the new part and it held. the oven is heating well now.

Parts Used:

Ann from El Dorado, AR
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

element burned out

pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.

Parts Used:

PETER from BROOKFIELD, WI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

My element caught on fire. After it cooled it snapped.

I unplugged the stove and used a flashlight for light. I tried a phillips head, but it was too big. I then got a set of pliers and unscrewed the two screws an pulled out the element. I removed the 2 electrical plugs from the ends of the element and attached the new ones. They went on from the top where as the old ones slid from the side. after pushing the element back in i screwed the screws back in and the backings were a tad large so I bent them up and presto it was fixed!

Parts Used: