KBSD612ESS00 KitchenAid Refrigerator - Instructions

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

diagnosed the problem to be the emitter and receiver boards. replaced in about 15 minutes. works like new!

Watched video of similar model repair for filter housing. But the model KitchenAide refrigerator requires enter and replacing housing from the back. My model has a metal facing which has doors attached to it also. It was simple repair though from the backside of the appliance.

Watched the video...easy!

Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holder. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!

Followed the instruction video.

Over the last several years we have had several appliance repairmen try to fix the icemaker. One replaced the entire icemaker. We bought a booster pump for the water. After spending about $1,000 over the past few years trying to fix the problem, a plumber doing routine plumbing work looked at it, and said it might be the control board. I found instructions online how to test the control boards. I ran the test, and they failed. I ordered the parts from PartSelect, followed their easy instructions, and tested the new units. They passed with flying colors. We now actually have an automatic icemaker for the first time in years.

The repair went OK, it is done. It would have been easier if a nut driver was not needed. Plus the location of the nuts was a bit difficult to manage a removal but not impossible.

I had to remove ice storage compartment sitting above motor on door to expose auger gear. Then used a small socket to remove 4 screws from underside of auger motor compartment in door. Motor drops out with a small wiring harness attached. This simply unplugs and then swaps in with new motor. Auger axel was sanded to remove rust and grease applied. Motor door and ice compartment were then reattached.

Unplug fridge, turn off water to fridge
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line

Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.

Removed old ejector arm and installed new part.

1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove two mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.

Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.

My ice maker just stopped filling with water one day and after some troubleshooting, I found that a chunk of ice had built up in the tube between the water supply line and freezer. I took the ice maker out (Don't touch the heating element...it really hurts) and defrosted the ice obstruction by injecting hot water into the tube to melt the ice. I used a new plastic syringe you get with an infant over the counter drug and a bucket to catch the water. I noticed the ice cube mold was peeling and decided to replace the mold. The mold is an easy replacement as long as you remember how you took it apart. My mold had some glue or compound stuck to the side that kept me from getting the mold flush against the motor assembly housing so I had to uncrew and scrape that gunk off and reattached. Other than that, there was nothing to it. Now the ice maker is good for another 8 years.

Easy, just removed the ice dispenser and the left support for the dispenser so I could get to the bottom screw easier. Three screws held the mold in place. The bottom screw had to be removed completely, but I just loosened the two top screws and lifted the mold out away from the wall and then disconnected the wiring. The end cover snapped of easy with a screw driver. I then removed the three screws holding the motor. then pulled the motor off.(the next square part under the cover. I did this before I realized that I could use a small screw driver and stick it into the holes to remove the mold and not mess with the outer screws. After I removed the mold, I replaced the new mold into position, without putting the white forky looking part back on so I had to take the two screws out and put the part in place before attaching the motor back to the mold. Everything went back together just like a charm. The ice maker is working good, easy job. Gone golfing now.