KBLP36FMS00 KitchenAid Refrigerator - Instructions

I was amazed when Fed Ex pulled up to our front door the following day after I ordered the parts, I was wondering what they were delivering and to my amazement it was the parts I had ordered from parts select the previous day , thank you so much , you are awesome. My 73 year old husband who is a 5 year cancer survivor had the part installed and we were ready to start making ice within 1 hour.He went by the installation information sent in by your customers. Thank you all, Jo Mesplay

Installed the icemaker control assembly this corrected the problem suspect contacts on the old unit were not making a good contact over time, due to the damp area in the freezer the new unit corrected the repair easy repair.

I first turned off the refrigerator. I then used a hair dryer to melt and release the ice by warming the bottom of the mould. Then I turned the fridge back on and let the icemaker discharge the ice. I then turned off the icemaker and ordered the new part. I unplugged the fridge, removed the icemaker (three screws and an electrical connection). Then I replaced the heater/tray with the new one and turned everything back on. Within a couple of hours we began having ice again.

first i removed 1 screw, then pulled out the ice maker, unpluged the electrical wire, i removed the white plastic cover , then an additional 3 screws . i pulled off the ice maker control . replaced with new ice maker control. i repeated the steps to put back the ice maker ...so
super quick part delivery !!!

I removed the cover to assembly ,3 screws and it came right off. points were wore out. Thank you for a prompt delivery. It was delivered much faster then I expected.

Paul First time dealing with you ,thanks

Repair was replacing motor kit. I did not use the plastic parts - ejector arm and separator. Went same as others described. I had removed ice maker from refrigerator although this was not necessary to replace motor unit(Please unplug refrigerator whether or not you remove the entire ice maker).
Removed three screws, removed old motor unit, inserted new unit making sure the ice level wire arm end was in slot. Ejector is D shaped so can't go in wrong. Replaced screws and replaced ice maker in freezer. Note - be sure the water tube is in the trough before trying to refasten ice maker.
Added note: If for whatever reason you need to remove ice maker note that there are three mounting screws (others have mentioned this) Completely remove one under middle of ice maker. For the two at top of ice maker - just loosen a few turns. The ice maker can be lifted and pulled away from the wall without removing these screws. Also there is a tab on the electrical wire connector for ice maker at back wall of freezer. Tab must be depressed with a flat tip screw driver while pulling out to remove wire connector. Tab is on wide side of connector facing inside of freezer.

Repair worked. Have lots of ice again.

Took the front of the ice maker off. Noticed the arm inside was broken, found the part on your site and ordered it.....super fast delivery. Replace the moter assembly and off she went. had ice in about 30 minutes. Thanks for your services and I will highly recommend you to others......Thanks again.

Installed new motor control

Removed the control and motor assembly by removing the plastic cover and three screws. Shut off the power to the refrigerator while removing the control and motor assembly (and also when installing the new one). Tested the motor using an AC power cord. The motor had apparently failed. Ordered the repair part and installed it taking care that the motor drive shaft and shut off arm were correctly aligned. The icemaker began to work properly when power was restored. The cost of this repair was about half the cost of replacing the entire icemaker.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

I had to order the module. It was easy to install. If i could have ordered just the gear and shaft, would have been a lot cheaper. Thanks for the addvise. Bill Paisley

After my son-in-law told me where to change the part, I had to use pliers to turn the knob and it came right out. I replaced the filter turned the knob.

followed the instruction video,that PartSelect provided on the web site,It was very easy

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Unplugged the frig., removed three screws, pulled the motor out, then slid the new motor in. Within a few hours I had ice again. The only problem was I felt the motor was still hooked to something after I took out the screws. Just be firm and pull it out, the pressure you feel is the thin bar that slides into the back of it to monitor the level of ice in the tray. It was REALLY easy.