Models > KB26G1XTG3 > Instructions

KB26G1XTG3 KitchenAid Mixer - Instructions

All Instructions for the KB26G1XTG3
61 - 75 of 146
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken gear case.
Remove and replace gear case. Apply food grade grease secure with screws.
Parts Used:
Gearcase Housing with Gasket
  • David from CEDAR CREEK, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
REPLACE SPEED CONTROL SWITCH
REPLACE SPPED CONTROL SWITCH
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • FRANCISCO from SAN BENITO, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
Parts Used:
Worm Following Gear
  • Stuart from Pittsford, NY
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed switch bad and Initially thought new part was wrong!
At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Richard from Harrodsburg, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • EBEN from WEST PALM BCH, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad control switch, striped worm follower gear.
Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
Parts Used:
Worm Following Gear Mixer Thrust Bearing Kit Mixer Lower Bearing
  • Bruce from EUREKA, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
attachment planetary gears stripped
removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.
Parts Used:
Hub Gear Gearcase Housing with Gasket
  • John from ST AUGUSTINE, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Planetary Pinion Gear Assembly had dropped down
The repair was easy, I only had to order new gear assembly parts and to replace the associated worn parts (shaft, pin, and gears).
Parts Used:
Hub Gear Worm Following Gear Mixer Retaining Pin Mixer Lower Bearing
  • Karl from Hammond Ranch, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set, Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The stand mixer would not rotate at low speed. Upon disassembly found one of the two alignment pins of the upper gear case broken.
1. Removed the decorative band then the upper motor cover.
2. Removed the upper gear case cover. Found one of the two alignment pins broken.
3. Inspected gears.
4. Cleaned out old grease.
5. Repacked with new food grade grease.
6. Reassembled.
Parts Used:
Gearcase Housing with Gasket
  • Russell from NEW LONDON, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Parts Used:
Mixer Worm Gear Worm Following Gear
  • Jerry from Southport, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gear teeth worn off worm gear
replace worm gear
Parts Used:
Worm Following Gear
  • Jamie from Jamestown, ND
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken gears
Fast
Parts Used:
Hub Gear
  • walter from SOUTH ELGIN, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part broken
Easy thanks to your instructions
Parts Used:
Bowl Arm Lift
  • William from North Olmsted, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed control would go from a "mix" setting 1 to a whip setting "10" by itself.
When I ordered a replacement assembly, I was sent a "new" replacement. As I had read up on your site to number the 5 wires BEFORE I removed them, this was a great idea. The new assembly was wired differently than the original board. Although no install instructions came with the new part, it was just a matter of connecting the NUMBERED wires to the new configuration. The first time I fired it up after plugging everything in, nothing happened! I removed all the plug-in wires and reinstalled to ensure I had not gotten a tight connection because of the plastic covers over the end connectors. On my second try, everything worked as advertised! VIOLA!!!! It was a bit tough because of the tight spaces within the motor housing and the new wire routing. Just take pictures of the area BEFORE you disconnect anything and you should do o.k., since I did. 20 minutes.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Joe from CASTLE ROCK, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Parts Used:
Stand Mixer Speed Control Board and Knob (Black)
  • Madeleine from NEW YORK, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KB26G1XTG3
61 - 75 of 146