K45SSBFOB0 Whirlpool Mixer - Instructions

Pulled off end cover. Used the how-to video's to show me how to remove the (3) components (watch out when it comes to removing the spring). Removed all (3) components (one issue was the black cardboard seal, which because of its age broke. Hindsight tells me that I should have purchased a replacement seal along with the (3) new parts.
Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.

Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thanks for having our parts and guiding us with a diagram of the unit. Very helpful.

I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok

Order the worm gear part number PS11748374.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk

I would recommend two people if possible.

1. Removed the mixer back plate Cover. 2. Removed the Speed Control Plate and retained spring, wires and ground wire. 3. Removed the old Speed Control Plate screws. Noted Control Plate pitted contact. 4. Removed old Triac Phase Control Board. 5. Removed old Governor. 6. Installed new Governor. 7. Installed new Phase Control Board. 8. Installed new Speed Control Plate and retaining spring. 9. Reattached Speed Control Plate wires. 10. Adjusted Speed Control Plate Screws and set mixer speeds from Stir to maximum settings. 11. Replaced Motor Brushes on left and right side of mixer. 12. Reinstalled mixer back plate cover.

Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.

Follow a YouTube video step by step

i disassembled the mixer until i could remove the worm gear; is in a housing that that includes another gear and shaft. make sure you have a magnetic tray to put parts in as you work or you will spend more time looking for parts than reassembling the mixer. once you have the gear housing out you will need a small diameter punch to drive out the pin that holds the gears in the housing(i used a 5/32 transfer punch.) make sure you punch the pin out where it will be caught or you will need to order that part because you will not find it. after knocking the pin out it is just a matter of removing the old gear, putting the new one in, and reversing the steps and getting everything reassembled.

watched an internet video to see what to do. Unfortunately even after replacing the chip the mixer it still didn't work.

Used the diagram on the website and a video
Totally worked!

Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.

I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!

Skewer the screw in with my fingers,

The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we could keep it going.

Just put on the new whip...exactly like old one.