JVM1630SPC General Electric - Instructions

The first thing I did for this repair was call a repair guy to come out and fix it since I didn't want to deal with it. After the initial shock of the $617 estimate to replace the Main control board, I scraped myself off of the floor and proceeded to look up how much a new board would cost me. The part was $155.04 at this site Much cheaper than the $417.00 estimate for parts I received from the repair guy. I could see from the drawings that the control board was on the back of the unit with its own access panel. It took me about 2 min the remove all the screws holding the panel on and another 8 min to remove the connectors from the old board and plug them into the new board......and another 2 minutes to screw the panel back on. The labor estimate I got was $200.00. Which comes out to about $800 an hour for the repair guy to do this job. One thing to note: Be sure to ground your self when you are touching the new board. Static electricity from your body can short out the micro electronics on the board

got a screwdriver and opened the glass door over the light bulb - changed the bulb and put the glass door back with the screwdriver.

removed frig bottom long drawer, removed the 2 narrower drawers above that. removed 2 plastic plates above the long drawer and unplugged pigtail. removed lower drawer slides and the back coil cover. removed small shroud that contained the fan pigtail and then removed the fan and replaced with the new one. fixed cooling issue and took 10 minutes from start to finish.

I removed the top of the dryer (unscrewed from the inside to release the top). Removed interior screws to pull open the front of the dryer. Once inside, it was really visible that the old parts (front air duct top and bottom) were in bad shape. They were cracked and broken. I removed the old pieces (they pretty much cracked and crumbled right off). I snapped in the new pieces careful to avoid damaging the electrical connections and wires. Once snapped into place (top and bottom), I careful put the front back into place making sure that the dryer drum rested on the new pieces. All screws back in place and all done! Dryer is now working as new!!!

Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !

Inserted handle into slots

Replaced cycle thermostat.

my problem was easy, i orderd a new lint filter, for a
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......

disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working

I reviewed the video instructions on the website; these were invaluable to understand the task. Since the dryer drum had to be removed to replace the thermostat, it was prudent to replace the drive belt at disassembly. Great job on the videos to see the extra effort required to install the new belt around the tensioner pulley while supporting the drum. I will use this site again when a need arises, because they are quick to ship the ordered part(s) and help the DIY handyman make repairs via the videos.

When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!

First, I unplugged the dryer, carefully so as not to electrocute myself. Then, I removed the panel on the top, back of the dryer, using a Phillips screwdriver. Then I removed the old timer and unplugged all the connectors, one at a time, so as to make sure I plugged them back in to the correct positions on the new timer. I had to use pliers because they were very hard to remove. Then, I plugged them into the same positions on the new timer, which was easy. Then I replaced the timer into position. Then, because I could not use the old knob since it still had part of the old cheap soft plastic post stuck inside it, I took a knob for the power rinse control off of my washer, since I never use that anyway, and I put it onto the new cheap soft plastic post on the new timer, and it works like a charm. I plan to be very, very gentle with that knob, knowing, as I do, that the post that it turns is not much harder than room temperature butter and that, if I break it, it will cost me over $70 dollars to get another one, and it also will not even contain a new knob, even though the one I borrowed from my washer will be unusable because it will have half of the old post stuck in it. Finally, I replaced the panel on the top, back of the dryer and plugged in the dryer.

So I replaced a burnt out defrost heater; replaced the thermostat for good measure and STILL the freezer compartment was freezing up. WHY didn't I look more closely at the ice making system sooner!!?? Thought about it for a while and decided that it had to be that the solenoid in the water valve was NOT shutting off water flow to ice maker (overflowing the icemaker and running over & down interior of freezer compartment making an icberg).

Took off about 4-5 backcover screws with one size nut driver. Moved to a size larger driver to remove 1 screw holding on the water valve. And what some people don't realize is that you can push in the connectors (push them down) and THEN pull the water lines out as long as you're careful and someone hasn't already tugged on the waterlines with some force. You don't have to cut the lines off at the valve. Put the water lines in the new valve and put one screw back in it; then 4-5 backcover screws and you're done!!! At most 15 minutes...that is if you want to clean the condensor unit located behind the backcover (on the newer models within the last 4-6 years).

EASY!!! Do it yourself and save a BUNCH of money. If you're getting a flooded freezer compartment or icebergs created in there then check whenever you hear the icemaker drawing in water and see if water is running down the interior.....problem solved!

Opened the package. Set screw fell on floor. Luckily cat found it right away. Fight the cat for the screw. Dug through my tools and the first Allen wrench I picked up fit. "What the hell? That never happens so obviously the screw won't fit," I think to myself. Put the screw in the hole and give it a few turns until my fat finger can't hold it. It's a miracle and the thing fits! Fight the close quarters with the Allen wrench to tighten it. Works like a charm!! Now I don't scare myself when I open the door thinking I'm going to rip the handle right off. Now I have easy access to my ice cream. The parts finder tool on the website was really easy and I found what I was looking for.

I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.