JVM1490SD003 General Electric Microwave - Instructions

I had left the door to the microwave open and turned around and hit the door latch assembly with my arm, sanpping off the bottom latch hook. In an effort to take apart the latch assembly it was necessary to take off the door choke cover and in doing so I sanpped a few of the plastic tabs that hold it in place. Undismayed, I then went online, found PartSelect, ordered the replacement parts, received them in three days and in fifteen minutes fixed both of them. The diagrams on the site made it easy to find what I needed and ordering the parts was easy. Thanks PartSelect-my wife is happy again!!!

Part delivered in2 days - awesome!Used the putty knife to get under the tabs to pull the cover shield off to get at the door "innards". Needed to take the underpanel out 6 small phillips head screws - non-magnetic so be careful you don't lose them.Pulled the shield of and the door comes away. Becareful not to drop it. Handle and latch went on quickly and as expected - put parts back in reverse order and off yuo go. Door works as good as new.

Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.

Remove door from unit. Place on cushioned service. Carefully pry plastic frame on inside of door to expose upper screw hole for handle. To gain access to lower screw hole, the inner metal frame must be removed. First, remove screws holding metal frame to door. Now carefully pry back the plastic tabs on each side. Once tabs are freed, metal frame easily removes. Install new handle, snap metal frame back, reinsert metal screws, then resnap plastic frame into place.

Read instructions and viewed video. Project would have been very difficult without the instructions and video. Step 1 removed vent grill at top to microwave, by removing two scres. Step 2 removed microwave door by lifting. Step 3 used a one inch plaster knife to separate the plastic interior cover of the door. The video was most helpful. Use the thin blade of the plaster knife to locate snap locations of the plastic cover. Step 4 removed broken latch by applying slight pressure to the outside. Observed the attachment of the 'spring'. Step 5 installed new latch and spring. Step 6 reinstalled interior plastic cover. Step 7 install door. Step 8 install vent cover with two screws. Step 9 test unit.

take the door off. The door lifts up and off. Once on a flat surface the job became must easier

I removed the plastic perimeter molding from inside of door.You can carefully pry it loose with a narrow putty knife. the door handle screws are located directly behind were the handle attached to the outside of the door. I found that a #2 phillip head screwdriver tip with a large handle for good torque and grip works best however the old plastic post inside the face of the door were turning along with the screws from the opposite side. I used a needle nose plyers to hold onto the plastic barrels in the outside of the door while turning the phillips head screwdriver on the inside at the same time. I found this to be somewhat difficult.You must achieve a good bite with the pliers!

I used a thin flat bar and a painters utility tool to pry the interior 1 1/2" plastic perimeter cover off. This is the most difficult phase of the project. The four corners have heavier duty clips that did not break off and easily were enough to hold the cover in place again after handle installation. Unfortunately the additional 10 to 12 smaller clips mostly broke. Still not a problem. Once this outer ring was off the upper handle screw was accessible, but to get to the lower screw I had to separate the outer door cover and a metal hinge mounted frame. There were (4) small phillips screws to remove and then again another clip removal to separate the last of the door components. FYI- this also required flat bar tools to lever the 6 or 8 heavier plastic clips that also hold the outer door cover and glass frame onto the metal door frame that is attached to the hinges. Once all apart the handle replaced simply and fit well. It went back very easily. Within 2 minutes I had it all back together and the outside wiped off of my fingerprints. The most difficult part was the first phase in trying to carefully remove the 1 1/2" interior plastic perimeter piece. 2nd most difficult was to the last prying required strong hands and might be better completed by (2) people. Other than that- it was a piece of cake.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.

The instructions were great!!! It was difficult to take the face plate off without breaking the nibs off that hold it in place. Other then that the only issue I had was removing the broken piece that was cemented in place by the years of super glue. Had to drill it out and almost drilled out the receiver plate to hold the screw/handle in place. I have to say this saved me $400 because I was just about to buy a new microwave because the broken door handle had driven me crazy over the last 3 years.

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

This wasn't easy to do, it would have been better to have two people. Taking the plastic trim off the inside of the door is tough, and only gets you access to the top screw. (You need to take that trim off to remove the door, and you have to put the door back on before you put the trim back, by the way.) You have to remove the shield covering the glass in order to get to the bottom screw. I didn't think I'd be able to get that shield off, and another set of hands to help pry it up would have been helpful. All in all, it's worth doing because the part is only $40 or so, but I can't call it an easy fix. Also, since the top of the handle had broken where the plastic screw sleeve meets the handle, and the screw was still inside the sleeve, it was almost impossible to get the screw out. Needlenose pliers wouldn't do it. I finally had to use a drill to drill away at the plastic sleeve until it was almost completely gone to get the screw out.

bought a fuse but that didn't solve the problem. Guess I need a new microwave