JVM1490BD03 General Electric Microwave - Instructions

Read other folks on your site on how they did it and I followed their directions. About 30 minutes and it was done. Figured I saved lots of money. Thanks

the problem was the mounting bracket that was installed when the house was built ,was not the bracket that came with the microwave. It was used to step the microwave out 3" in front of the other cabinets for the style that they were using then. so when I was installing the new cabinets I didn't want that style, so I ordered the original mounting bracket. It was a perfect fit and the install went great

Removed inner trim panel. Bottom screw was visible But upper screw was behind metal frame that trim plate snaps onto Removed that to access screw. Door latch had to be removed to. Not a big deal just be sure spring on latch is reinstalled same way it was removed. Took longer than expected but way cheaper than a service call. Part arrived on time

Removed plate inside door cover and removed old screws and plastic handle. Reassembled.

Replaced the fuse. Result; did not fix the problem.

removed screw from inside wall. removed leftover board & replaced with new board & screw. good as new!!!

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

removed key pad then removed latch assembly and replaced it with new latch assembly.

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

Replace the fuses

Part delivered in2 days - awesome!Used the putty knife to get under the tabs to pull the cover shield off to get at the door "innards". Needed to take the underpanel out 6 small phillips head screws - non-magnetic so be careful you don't lose them.Pulled the shield of and the door comes away. Becareful not to drop it. Handle and latch went on quickly and as expected - put parts back in reverse order and off yuo go. Door works as good as new.

My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...

First I called General Electric and was told they had the vent grille part and would ship it for $95.00. I then went on line and found the same part number at PartSelect.com. They quoted me a price of $75.00 and I purchased it on line. It arrived within 3 days and had the new vent grille on my G.E. Profile Oven/Microwave within 30 minutes of opening the box. All I did was remove the two screws from the broken grille, removed the grille and put on the new vent grille with only a screwdriver. I highly recommend Parts Select as they exceeded my expectations.

The primary door latch switch contacts were not closing properly. I broke the latch bracket while removing the switch. It is only a plastic clip that holds the switch in place. I replaced the switch and bracket. The Advantium now works in all modes.

I had left the door to the microwave open and turned around and hit the door latch assembly with my arm, sanpping off the bottom latch hook. In an effort to take apart the latch assembly it was necessary to take off the door choke cover and in doing so I sanpped a few of the plastic tabs that hold it in place. Undismayed, I then went online, found PartSelect, ordered the replacement parts, received them in three days and in fifteen minutes fixed both of them. The diagrams on the site made it easy to find what I needed and ordering the parts was easy. Thanks PartSelect-my wife is happy again!!!