JVM1490BD002 General Electric Microwave - Instructions

take the door off. The door lifts up and off. Once on a flat surface the job became must easier

Remove door from unit. Place on cushioned service. Carefully pry plastic frame on inside of door to expose upper screw hole for handle. To gain access to lower screw hole, the inner metal frame must be removed. First, remove screws holding metal frame to door. Now carefully pry back the plastic tabs on each side. Once tabs are freed, metal frame easily removes. Install new handle, snap metal frame back, reinsert metal screws, then resnap plastic frame into place.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

I used a thin flat bar and a painters utility tool to pry the interior 1 1/2" plastic perimeter cover off. This is the most difficult phase of the project. The four corners have heavier duty clips that did not break off and easily were enough to hold the cover in place again after handle installation. Unfortunately the additional 10 to 12 smaller clips mostly broke. Still not a problem. Once this outer ring was off the upper handle screw was accessible, but to get to the lower screw I had to separate the outer door cover and a metal hinge mounted frame. There were (4) small phillips screws to remove and then again another clip removal to separate the last of the door components. FYI- this also required flat bar tools to lever the 6 or 8 heavier plastic clips that also hold the outer door cover and glass frame onto the metal door frame that is attached to the hinges. Once all apart the handle replaced simply and fit well. It went back very easily. Within 2 minutes I had it all back together and the outside wiped off of my fingerprints. The most difficult part was the first phase in trying to carefully remove the 1 1/2" interior plastic perimeter piece. 2nd most difficult was to the last prying required strong hands and might be better completed by (2) people. Other than that- it was a piece of cake.

The primary door latch switch contacts were not closing properly. I broke the latch bracket while removing the switch. It is only a plastic clip that holds the switch in place. I replaced the switch and bracket. The Advantium now works in all modes.

I had left the door to the microwave open and turned around and hit the door latch assembly with my arm, sanpping off the bottom latch hook. In an effort to take apart the latch assembly it was necessary to take off the door choke cover and in doing so I sanpped a few of the plastic tabs that hold it in place. Undismayed, I then went online, found PartSelect, ordered the replacement parts, received them in three days and in fifteen minutes fixed both of them. The diagrams on the site made it easy to find what I needed and ordering the parts was easy. Thanks PartSelect-my wife is happy again!!!

Removed. Inside frame with putty knife replace new latch attach spring and line up notch of latch in slots. That was the most difficult part replace inside frame. Done!

My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...

Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Take the pliers and place a tight grip on the broken rack bracket, twist toward front of microwave until loose, pop out and by hand insert new rack bracket, twist toward the back of microwave until fully in place. One side was slightly harder than the other taking off and replacing rack bracket.

Part delivered in2 days - awesome!Used the putty knife to get under the tabs to pull the cover shield off to get at the door "innards". Needed to take the underpanel out 6 small phillips head screws - non-magnetic so be careful you don't lose them.Pulled the shield of and the door comes away. Becareful not to drop it. Handle and latch went on quickly and as expected - put parts back in reverse order and off yuo go. Door works as good as new.

Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks

I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.

Called my local appliance repair shop when the handle broke off my GE Advantium microwave. They told me the price of the handle, but said the door would need to be replaced as well. This is because the plastic tabs break off the inner door panel when it is removed. They estimated a $400 repair cost. I ordered the door and installed it for around $45. The inner panel comes out, and most of the tabs do break off. I was able to disassemble, install the new door, and reassemble. The inner panel stays right where it belongs, even though I broke off a few plastic tabs. Werks goood.

I went on line and found the part and read all the comments that had been written on how to repair the door and I found the directions on how to take it off and put it back on, so it helps to do your research on taking it off and putting another one. My son-in-law did it for me, it was quite difficult to remove the screws,and it took about 30 min to remove the door and take the screws out, but putting it back on was easy and took less than 5 min. So I was pleased, the part was ordered on Sat and came by FX on Tuesday, I was very happy with the service, and it works as good as new. Just do your research, that helped a lot.