JS42FSDBDA Jenn-Air Refrigerator - Instructions

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

The fan motor was burned up affecting the efficiency of the refrigerator. I removed the fan motor, tested it, ordered a new one and installed. saved 100 bucks in service call charge and got great service in delivery from parts direct. Ordered on Thursday and recieved monday.

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

Checked the ice tray and could only find the drive ring had some breaks in the plastic. Actually did not see why this would stop the auger from turning and dispensing ice. However this was the only thing I could find wrong with the unit. I pulled the tray, removed 6 screws (star tip heads) pulled the auger forward and replaced the drive wheel, put the unit back together and its been working fine ever since.

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

Pulled socket out of housing, unplugged it from source, plugged in new socket and replaced the socket into housing, screwed in bulb and it worked!!

took the old one out, put the new one in, reset the Refrigerator-Light 5 min. job. Tanks for the fast delivery B.Z.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Very simple. Unscrew old filter, following instructions on new filter's box, install new one by hand.

Easy disassemble removing screws to separate front of ice bin.Be sure to note how metal rod is attached to rear of ice bin. Installed drive ring and reattached face (front) of ice bin in about 15 minutes.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Problem caused by ice cubes falling out of ice bin and collecting at rear and interfering with ice dispenser drive. Broke plactic drive ring. Pull down 2 clips at front bottom of ice bin. Pull ice bin out. Dump ice cubes. Remove 8 star drive screws to allow case to move far enough to clear broken drive ring. Replace drive ring. Reinstall and tighten 8 screws. Install ice bin. Correct loose right side ice cube retainer board to prevent cubes from falling out of ice bin.

Carefully removed all of the screws to get to the compartment which housed the broken circular door that seals the ice compartment after ice has been delivered via the water fountain on the front of the refrigerator. Disconnected the wire harnesses (labeled as I went) and pulled the unit off of the fridge. It would probably be wise to have shut the power to the fridge off, although I did not. The problem was that the circular door that snaps back into place after delivering ice had severed one of the tabs that holds it in place. I discarded the old door and slipped the new door into place. There is an electromagnetic plunger that is responsible for the door opening when ice is being delivered (the system is magnetized and it draws the plunger in, thereby opening the door) and then snaps back into place once the ice button is released. I found the best way to get this back into place was to put the door (with its harness) into the "open" position and then gently force the plunger into place. Put everything together and all was good.

Removed back cover to see motor and the fan. Un plug the fan motor from the fan. Used 1/4in socket to remove 3 screws, then unscrewed plastic mounting plate off of motor, put plate back on new motor, used pliers to remove nut from fan blade,and rubber washer replaced to new motor. Then put new motor back in. Make sure motor is centered back in hole and fan does not hit. The brackets (3) that hold motor in place will swing so it can be centered in hole. Spin blade to make sure blade not hitting and is centered. Now plug fan motor back in. Just that simple.