JMP26G4J4 General Electric Range - Instructions

First, and most importantly, flipped the circuit breaker and turned off the power to the oven. Next, Unscrewed the old element and disconnected the wiring. Then, removed the old element and replaced it with the new one.
Reconnected the wiring to the new bake element and screwed it back onto the oven.

Voila! Turned the oven on and watched the new element heat to a bright red. We had an oven once again, and saved ourselves more than $100. Yay!

The Baking elements takes 10-15 minute each but the Broil Element is a bit tricky as the screws holding the element is difficult to get to. I also used duct tape to temporarily hold the element to stay in place.

Ordered Bake Element - 240V from Partselect , when part received removed broken element with a screwdriver., replaced with new Bake Element with a screwdriver. Very easy to do.

Ever the optimist, I'd replaced the burner on this relic of another time to no effect. That left the switch. You guys should know that when a burner element goes bad it can take out the switch. I should have put a meter on it. Wehn I looked for a replacement a few months ago there were still factory parts available, but they were $80 or so and I wasn't inclined to risk that on a 40 year old range. I offered to replace the raange for my daughter as a Christmas present but she like this old thing. It was an unusual size with a pan storage compartment on the left. I went on line and found this universal replacement for about $25 delivered. What the heck. I ordered it and it arrived within a week. I pulled the stove out, killed the breaker, pulled the knob off, used a nut driver to take ther rear panel off, two phillips screws under the knob hold the switch in. The terminals on the old switch are in a slightly different order but are clearly marked L1, L2, H1, H2 and P. The P is the power and has a smaller terminal so you can't put it on the wrong one. Just examine the old switch ( it was marked the same way) take off the L1 and put in on the L1 of the new switch and so on, make sure you use the correct knob adapter to fit your old knob and break the switch stem to the correct length. It will break easilly if you hold it with one pliers and break it with another. Screw the new switch in place with he old screws. At this point, I closed the breakers and tested it. It worked fine. I turned the breakers off again. Buttoned it up and slid the stove back into place. 20 minutes tops. Great product. Good for another forty years.

First I removed the two screws in the back. then I removed the two screws attached to the brace at the top. pulled the old element out. Removed the screws that attatced the wires to the element. Attached the wires to the new element. Pushed the wires back in. Pushed the element in and attached the screws. Reattached the support. Turned on the broiler. The element smoked for a few seconds before getting red hot. It is working fine.

Pull the stove out from the wall and unplug. Had to remove back of stove, the aluminum sheilding and the duct work to get at wires use nut driver. Then used nut driver to remove nuts from broiler unit inside stove. Take the front overn dover off first. The new part did not match up with the wires so I used a needle nose to spread the wire clips just a tad so they would fit over the tabs of the broiler unit. Do all of this behind the stove as you do not have eough wire to do this effectively from the oven side. After I had the tabs fitted to the broiler unit. I removed them and fed wires back through the stove. I then went back to the front of the stove and put the broiler back in and put support bar back in to ceiling of stove and the two nuts back on to affix broiler to back of oven. Put the aluminum baccking and duct work back onto the back of the stove and plugged it back in. Pretty easy job.

Turned off power at panellboard. Disconnected mounting hardware from inside oven chamber. Pulled failed heating element with wires attached into the oven chamber. Disconnected wiring and reconnected them to the new heating element. Tightened screws while holding connectors with pliers. Applied electrical tape to connections. Pushed wires back into opening and secured heating element back into place. Restored power nad verifed proper operation. The other heater purchased will be used when the bake element finally fails,

(1) Turned off power source.
(2) Removed rust on screw heads before attempting to loosening them up.
(3) Pulled the element out to expose the connections.
(4) Disconnected with phillips screw driver, taped off wires to prevent mixed-up during re-installation.
(5) Re-installed new element using new screws provided.

Removed the racks, removed two screws holding the element to the back of the oven, removed two screws holding wires to the element, installed by the reverse. BUT in my case the new element still didn't heat. The part was perfect so when the old element melted and shorted, it must have damaged the controlling switch (220V requires dual pole switch--apparently one side is now bad). Since the oven is over 30 yrs old, I'm returning the element and will buy a new oven.

this repair is simple. Just unscrew the existing connection and attach the new heating element. You may have to break the existing ceramic element, but a new one comes with the new heat element.

I turned off the breaker to the oven. Removed the old element and replaced. Turned on the oven breaker and turned the over to 350 and it was working great. I was very proud of myself as a 68 year old widow.

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

Removed single screw securing the old tilt-up burner. Removed clips on sides of clamshell ceramic terminal block with flat blade screwdriver to expose two wire connections. Removed 2 screws connecting the wires to the bad heating element. Did not use the supplied new ceramic terminal block, just reused old one. Connected new burner to wires with 2 screws. Reassembled terminal block with clips. Fastened clip with single screw to attach new unit to side of opening in range top. Tested. Done.

Turned off the power to the oven. Removed the racks. Removed two screws holding the unit to the back of the oven. Removed two screws holding the wires to the terminals. Removed the old unit. Reversed the process. Piece of cake. The only "difficulty" was that the old wire-to-terminal screws required a nut driver (as did the unit-mounting screws) while the new wire-mounting screws required a #2 Phillips screw driver. Took me a couple of minutes to get one of those from the garage.